Search results

I am installing belltech drop shackles and hangers and well i was able to install the shackles but when i try to install the hangers the eyebolt on the leaf springs dont coincide with the drop hanger. its probably half an inch off how do adjust it to coincide? Any help would be greatly...

I just replaced my O.E. filter that came with my Fass 220 I went ahead and got the cross reference fleet guard filters from my local fleet guard. When I went to start the truck I heard this loud clanking noise coming from the filters. It sounds terrible is this normal?? I never noticed that...

Hey guys im running a s363/s480 compound I am trying to figure out how to mount the turbos using 06towrig design but I came up on a dilemma as far as the heat exchanger is concern. When mocked up the primary was hitting the heat exchanger so I had it removed to see fitment and without it there...

I have a quick question I do see here a lot of guys running wastegates on there setup I have a steed speed and well unfortunately I didn't buy it with a wastegate. There isn't any good fabricator where I live so First Question Can I run a s363/s480 setup without a wastegate I know the issues...

Guys I am stuck on my fass install I took it to a shop and they ruined the whole thing I would like to know how the routing is once you have to tee the lines /i see the ofv has a hard steel line and goes into a rubber hose. I had removed the lift pump and heater but i am stuck on how to do this...

Alright guys so I am in a bit of a pickle here. In my earler threads i had decided to go with an s366 turbo with a T4 foot. I enjoyed the turbo and it showed me a good time. I did have an issue with the spooling as it was somewhat slower than my hx35. Now I just went ahead and sold it since I...

I have the truck in the sig I have a bit of an issue When I come to a complete stop while in traffic waiting for the light and then attempt to take off my truck takes a second or two to get moving forward. I have replaced the transmission pan no shavings were found and also replaced the filter...

Alright guys an update to the an issue im having ....got somewhat of a horror story a few months ago i had replaced valve spring and retainers to 165 pd hamilton i was doing the pushrods today when i saw this.... the exhaust valve retainer had cracked called hamilton immediately and they will be...

Hey guys I'm in a bit of a dilemma with my build as you can see in my sig below are my current mods I really don't know what to do next so far my list is a steed speed manifold and to increase the timing To 23 degrees. I would like to O ring the head but it seems to be too much money at this...

have a 97 2500 in which I Had my interior lights flickering on my truck turned out out to be my alternator going out so I went ahead and replaced it with a brand new one. The lights are still flickering not as bad but its there. As rpm increases the light stops flickering with both of them...

Hey guys I just installed some 5x.018 injectors I bleed the system and truck was running fine when I stepped out to check for leaks I notice injector#4 was leaking from the top of the feed line and the Hold down nut when I took a closer look. I made sure the line was tight any ideas just would...

:nos:I am looking to install some ARP studs on ]my truck I am having a difficult time finding a shop who can do it at a reasonable rate in South FL. So the last resort is me doing it myself I have read countless amount of threads on it but is it really simple to do? I went to a machine shop and...

I was looking around because I am at the point where gauges are needed for my setup when I came across the edge monitor for 96 and up vehicles. .Has anyone used it on their 12v if so can it provide me with the most important gauges pyro, boost, and fuel pressure? I am all for simplicity but a...

I currently have a 1997 12v in which I will be doing twins on now my question is I had purchase some Arp studs the 500 dollar ones and was told the rockers need machining and what not to fit the head studs. Then I came across this on ebay I was wondering if anyone has tried it...

:st: Well I just got this turbo from Forced Induction its a S366 /74/91 I would like to know what upgrades I would need I went to the cummins forum and it seems like its an obscure turbo but a good friend recommended it for me. So I went and bought it but I would like to know what supporting...