Search results

1Lb spool of Lincoln Electric .035 mig welding wire. Innershield NR-211-MP. $20 pick it up or add shipping to you.

Friends father in law passed away, he had a couple old Plymouths. Very good body's on them, the '51 could be driven with a bit of work, the '39 needs re-assembled. He has boxes and boxes of new parts. They are asking $3k for everything. Nobody in the family has the interest or ability to restore...

A friend has it, for sale, belonged to his deceased father, used mostly to pull 5th wheel camper. Never in snow pretty good condition, updated auto trans with engine brake and lock up switch, extra in bed fuel tank. Not sure of mileage, PM me and I will get their number for you. I believe they...

About 177k on it now. Motor has SmokEm 90hp injectors, 100 plate, Schwitzer S300, 4" exhaust. Isspro gauges. KDP tabbed. Bypass filter. Rebuilt trans with Dunrite TC and VB, Intelligent Engineering billet input. Rebuilt transfer case. Rebuilt Dana70 posi rear, with all new clutches and bearings...

Lots of stuff, 4" & 3", intake, boots, compressor elbow, etc. 4" 90* hard rubber elbow $25, 4" 45* hard rubber elbow $25, 2 3" 90* hard rubber elbows $20ea, oem 4bta intake elbow $45, 4" compressor outlet elbow fits HX30/HX35/ S300, $50, 3" soft rubber elbow $15, steel 90* tube 14" long $30, OR...

Twisted Innovations Dyno 3701 North Ridge Road West, Ashtabula, Ohio 44004 http://tidyno.net/main.html

Trying to sell complete as a parts truck, or fix it and put another couple hundred thousand on it. I am driving it everyday and it is PA inspected until 11-15. Will entertain offers on all prices. Complete truck $4995 176k miles. Cab and front fenders pretty rusty. Have good southern fenders...

1996 Dodge Cummins 2500 4x4 auto $5995 obo. It’s time to part with my old friend, I can’t justify keeping her anymore. I bought her to haul my racer, but gave up racing several years ago. I upgraded everything I repaired, planning to keep her forever. I typically get 19.5 mpg summer, and about...

4" HY35 outlet elbow, with O-ring, flex boot, and clamps. It was on my HY35, I believe it will fit HX35 also, not sure what else. $50, shipped? You can paint it any color you want.

Needed for my 4BTA. Any condition.

'96 Dodge 2500 Needed 4x4 to get into my parking space at the fair. When I left the 4WD light stayed on. Didn't seem to be binding, so I assumed the switch stuck. I know the disconnect in the front axle is working, I jacked it up and checked. The front drive shaft won't free wheel, it should...

I have a HY35 on my 4BTA and it's too big. I need to downsize. It was rebuilt before I got it, and now has about 5-6000 miles on it. It has a 4" elbow output, and a 3" exhaust. Sell it for $250 plus shipping. Trade it for a HX30 or hhe221.

Can one use older Dodge Dana 60 hubs, or stubs, or ??, on a later Dana 60, ('96) to eliminate the unit bearings, and gain lockout hubs? My eyes are starting to bleed from searching. I know there's a Ford swap, just having a little trouble finding those.

I have a fresh rebuilt TH400 with the full length cast aluminum pan, new torque converter, Cummins to GM adapter housing, starter, flex plate and wave ring, hub, Lokar floor shifter, Lokar reverse/nuetral safety switch, rear trans mount, and Mark Richards racing slip yoke. I am asking $1000 for...

I need an HX30 compressor elbow. Not sure if the 35 elbow will fit. The dimensions are 2" inlet, 2 7/8" widest part of flange, and the flange is just over 1/8" thick, and the outlet should be 2 1/2" but 3" will work. Needs to be a 90* or even a tighter turn. I have one with a 4" outlet which is...

Anyone from Northeast OH, or Northwest PA. 776 Center St, Ashtabula OH. Saturday October 20. 9am, 'til done. $75-3 pulls. Benefit Ashtabula County Animal Protection League. $15 APL donation items gets $25 off dyno pull. Cash and merch prizes for top HP and torque, lunch.

I'm hoping you have one laying around. It's the same as a HX35 outlet at the turbo, (2-7/8") but smaller diameter output side to the I/C. I can use a HX35 one, and just neck it down, if I have to.

Jedeka suggested I give you guys a try, I need an HX30 compressor outlet, prefer an elbow, but will take a straight one and use a rubber elbow. My HX35/S300 elbow off my other truck fits the flange, but the output side is too big, besides I need it for that truck. The one I need measures 2 7/8"...

Bought a rebuilt HX30 for my 4bt project, no compressor elbow or drain fitting. Elbow measures 2 7/8" across the flange, and 2" inside. Would need the clamp too. Drain fitting should be standard. Thanks.

The pin that goes into the cam gear from the back, to remove it do you have to remove the bolts from the front? Mines wrecked, (F'ing dealer!!!) and I need to change it. I can't feel bolt heads, and you sure as hell can't see the damn thing.