P-Pump it!! (info)

Tate said:
Here's the list I made from my kit. Quote me, then copy into notepad to get proper formatting. Also I am making a webshots album since there seems to be more interest in pictures. http://community.webshots.com/album/569265894Brlumf

If there is a better hosting place, let me know, I'm not too thrilled with that site.


Cummins P/N Desc. Qty. Add. Info

4003580 Pump support bracket 1
3924346 Tee fitting (Tee, BRN) 1
3928231 M8x1.25mm x 25mm Torx screw (2) 1
3928898 Fuel Pump Brace 1
3937123 M10x1.50 x 50mm Stud (4) 1
3913994 O-ring, Timing Plug 1
3907998 M5x0.80 x 16mm screw Torx (2) 1 Timing Pin housing screw
3902662 M10x1.50 Flange Nut (4) 1
3969698 O-ring, Pump Seal 1
3804899 Front Cover Lip Seal 1
3915772 Seal Ring 1 Cam Sensor Seal
3913366 M8x1.25 x 90mm Cap Screw 9.8 (2) 1 25mm long thread
3901445 M8x1.25 x 45mm Cap Screw 9.8 (1) 1 25mm long thread
3918673 Front Timing Cover Gasket 1
3938156 Rear Timing Housing Gasket 1 Between Block and Housing
3936256 Timing Housing 1
3931382 Pump Gear 1

Linkage Kit

3938397 Linkage Rod 1
3923158 Linkage Mechanism, Clock Spring 1
3923161 Bracket 1
3931527 Linkage Mechanism 1 Degreed from 59 to 73 degrees
3930407 Linkage Bracket 1 5 Tapped holes
3914353 White Plastic Bushing 1 Bushes 3930407 and 3923158
3990095 Linkage Rod End 1
??????? M6x1.00 x 101mm rod 1 40mm and 66mm long threads
??????? M6x1.00 nuts 2 Jammed together on above rod, on 66mm long thread
3931546 Bracket 1 Looks like a shifter fork
??????? Linkage Rod End 1 10mm shorter than 3990095
??????? Spring, 11mm OD, 30mm coil, 80mm long 1 Plastic clip on each end, marked 'B' and 'I'
??????? Spring, 12mm OD, 25mm coil, 90mm long 1 Plastic Clip on one end, marked 'E'
??????? Spring, 15mm OD, 25mm coil, 80mm long 1 Plastic clip on each eng, marked 'G' and 'J'
??????? M8x1.25 x 20mm Bolt, 8.8 1
??????? M8 flat washer 1
??????? M8x1.25 x 12mm Cap Screw 3 Flanged, 10mm head
??????? M6x1.00 x 15mm Cap Screw 2 Flanged, 8mm head
??????? M6x1.00 x 10mm Linkage Ball 1 25mm overall length, 10mm ball end, 11mm hex base
??????? M6x1.00 Nuts 3
??????? M6x1.00 Nut 1 Plated
??????? M5x0.80 x 10mm Cap Screw 3 Flanged, 7mm head
??????? #6-32 x 3/8" Machine screw 1 Flanged, 1/4" head, slotted
??????? Lock Clip 1




Not Listed by Scheids
3969988 Grid heater Gasket 2
??????? M8x1.25 x 200mm Socket Head Cap Screw 2 30mm long thread
??????? M8x1.25 x 180mm Socket Head Cap Screw 2 30mm long thread
??????? Grid Heater Spacer 1 Aluminum, 1" thick



Scheid P/N

2-915-032-031 M20x1.50 Nut 1 Pump Shaft Nut
2-916-699-091 M20 Lock Washer 1 Pump Shaft Washer
417ISB Cam Sensor Ad. Adapter, Cam Sensor 1
417ISB PP Line Kit P-Pump/ISB Injector Lines 1

Bosch P/N

2 413 455 013-000 M14x1.50 OD, M10x1.00 ID Nut 1 Reducer Nut

Aeroquip
657AERO1503-4 3/16 Aero Hose, 2 ft M51 1
657AERO4411-4-4S -4AN Swivel Connection M51 2 Crimped on Hose

Misc. P/N

139969 Pipe Nipple 1 Thread OD roughly 11mm or 7/16"
Click to expand...


Did you buy all these parts new or did you piece everything you dont have a part number for? Im just trying to get a idea of what all of this would cost.
 
PPumped 24V's are FUN! I got to go for a spin with Tim (warpig) the third Friday in February in CT, and that thing rips. Have some traction issues when nailing it rolling up a side road. Very impressive!
 
BearBeatsAll said:
Did you buy all these parts new or did you piece everything you dont have a part number for? Im just trying to get a idea of what all of this would cost.
Click to expand...

Thats everything that came in the kit, and anything that had a part number is there. Things like the springs and bolts just came in parts bags, no numbers.
 
Stupid question here...Why do yo need the TPS/APPS after the swap?
 
Warpig said:
24v P-Pump conversion

I've read of guys using their existing cables and modifying the p-pump linkage to accept the 24v APPS (TPS). I used a 12v TPS and a 12v TPS plug was spliced in.
Tim
Click to expand...


Tim,

Can you explain this a little further??
Also how did you wire in the 12v TPS?!

thanks,
scott

PS...you can probably tell I'm having issues. LOL
 
to wire in 12V TPS to 24V APPS wire harness

Pin 1 on the 12V plug (Black/blue tracer) for tps goes to the black/yellow tracer on 24V APPS Harness.

Pin 2 goes to Blue/black tracer.


Pin 3 goes to Blue/white tracer.
 
Signal 73 said:
to wire in 12V TPS to 24V APPS wire harness

Pin 1 on the 12V plug (Black/blue tracer) for tps goes to the black/yellow tracer on 24V APPS Harness.

Pin 2 goes to Blue/black tracer.


Pin 3 goes to Blue/white tracer.
Click to expand...

Scott, that's straight from the "Monkey" who wired mine :Cheer:

You need a 12v plug from a 12v wire harness.
 
If u wanted to use the stock bracket and cable U need to drill extra holes were they mount to the pump and I removed the rivet holden the small ball end drilled the hole bigger and mounted the Ppump ball end to hold the linkage.. Now this will vary usen a auto , but I'v seen it done too
 
You must log in or register to reply here.
Back
Top