F250/Cummins Swap

Need input on Ford intercooler boots. Looks like the mishimoto boots like to delaminate.

Sent from my XT1575 using Tapatalk
 
Ive ran siliconeintake.com boots on my last 2 builds, last truck i drove for 7 years no issues with them and my buddy still drives it

Sent from my SM-G950U using Tapatalk
 
Anyone know where these coolant hose adapters came from?
bac80bc75f6e11bef175fef7e250971b.jpg
fb6104ca70c949320fbb735fe7e74e38.jpg


Sent from my SM-G950U using Tapatalk
 
I meant on the 6.7L. I know what it has to do, but trying to come up with a way to plumb the return side that will look decent. I went and got the 12V nipple with two ports and put in my feed neck. I'm thinking about coming up vertically there and then down the side of the valve cover. It's either that or a version like the 6.7 down under the ex manifold. I don't want to limit turbo upgrades in the future.

Sent from my SM-G950U using Tapatalk
 
I ended up with a shift lever, one of each of the heater hose connections, and brackets cut out to attach the Ford shift linkage to the 47re case. Pics to follow.

Sent from my SM-G950U using Tapatalk
 
dustinjean said:
I bought a 5r110 shift lever but the ford cable clipped onto the 48re linkage so i only welded up a cable mount bracket for now, still trying to figure out my anteater issues

Sent from my SM-G950U using Tapatalk
Click to expand...
So you nailed it. 48re lever is almost the radius it needs, and the vertical offset is correct for the end of the Ford cable to pivot correctly.

The offset one is the one I made for fitup that didn't work.
64f8db7848f0d6547f34bc3f9f3e8ca7.jpg
623eae8809360303cb62d40fff579af4.jpg


Sent from my SM-G950U using Tapatalk
 
Yea i didnt touch the 48re arm on mine just welded the ford cable mounting point to the dodge 2 bolt mount then popped the cable onto the 48re pivot arm. Just annoys me that in reverse the pointer needle is between park and reverse on the dash and drive is neutral on the dash pointer. but in park its perfect guess i could adjust the needle where its correct for in gear and just off when in park though then it would not annoy me as much.

Sent from my SM-G950U using Tapatalk
 
biggy238 said:
I meant on the 6.7L. I know what it has to do, but trying to come up with a way to plumb the return side that will look decent. I went and got the 12V nipple with two ports and put in my feed neck. I'm thinking about coming up vertically there and then down the side of the valve cover. It's either that or a version like the 6.7 down under the ex manifold. I don't want to limit turbo upgrades in the future.

Sent from my SM-G950U using Tapatalk
Click to expand...

Does your engine have a coolant bypass on it? The clamps that come with the kit would be a clean way to plumb it down the side of the valve cover. I have 2 extra ones if ur interested.
 
Depends on which style you have available. I bought an older fleece with p clamps.

Sent from my SM-G950U using Tapatalk
 
Question of the day: will the 03-05 trans cooler lines around the back of the block fit with the fleece bypass?

Sent from my SM-G950U using Tapatalk
 
Driver side cables are on. Engine harness is finalized.

Engine runs. Probably have 5 minutes of run time on it.
e3b335bdf86d06a14158415d341a8f4d.jpg
22cfb7aca182f3b9a1ca5f9a7274840e.jpg
c3bd4a5e52f10dcea460a892bfca2af1.jpg
b782d2de088ed7d5081ab6397078bc43.jpg
04574870b2684329d7a02ea9fc07e2dc.jpg
69907a928368ef32f35849a5d2fc6c32.jpg
1dd62737a6ddd392dfff62600fce95fc.jpg


Sent from my SM-G950U using Tapatalk
 
Hahahaha I just spent an hour snaking these tubes in to my engine compartment and sorting how to get it mounted. I come inside and cruise Insta to see that PDD put up a picture of the exact thing I intended to do. Also checked oil pressure.
2729d45513d155724d7788a899bb1b16.jpg
ac879e8ff8ed1e2118a6434aba8a1249.jpg
714c06ad99782c8221b8b9e27d62bc0f.jpg
078d549f3b8eb0e46d3218dc7d4351f5.jpg


Sent from my SM-G950U using Tapatalk
 
You must log in or register to reply here.
Back
Top