Recent content by gearhart73

I’m looking for a 48re close to the central Ohio area for a swap. Just a good usable core. Going to be used in a 2wd application but either 2wd or 4wd would be good for the core.

I’m looking for a good used set of standard length 6.7/5.9 billet rods if anybody is going deck plate next season. I don’t really need them for my HP goal but wouldn’t mind the extra comfort if I push it either. You can PM me here or reach me at 740 two25 one 881

Dad wants to drive my 2010 around now but wanted it just deleted so I took the pump, injectors, and 2nd gen turbo swap off of it. All of the parts have been on the truck about a year and a half. I bought the pump and injectors new about 3 years ago and they sat in the boxes in the shop until I...

My 2010 has decided to throw a fit this week going down highway. Started off with the cruise control stopped working. Then the throttle would cut out for a second and red electrical light would flash on the dash while it did it. After a while that light stayed on and the service 4wd light came...

I bought this 2006 as a roller with a rebuilt title to build into a farm truck. It's regular cab 4wd st model truck with 218k miles on it. I went through the front and rear axles to put all new bearings, seals, u joints, and ball joints. And then the build turned into a little more than just a...

I have a set of 4 cut tires off of my super stock truck. They were new at the beginning of last season. Had less than 20 hooks and I had them sharpened before they were dismounted so they have a fresh edge. 34x18.00-15 (2) Pioneer Giant Puller. 4ply. Fronts (2) Pitbull Super Puller. 4ply...

I'm looking for a drivers side battery box for a 2006 dodge. The one in the roller I'm working on is busting out. I'm from Kingston, OH 45644. Let me know if you anybody has one and what they would like for it.

I have been working on putting an 06 roller that I bought together and I'm looking for some advise. I have put a 6.7 down in it and I have the 5.9 harness all piled up in the corner. I didn't take it apart and I don't have anything to use for a reference on how to route the harness and where all...

I have a 2010 STL model and I'd like to convert to the newer Laramie seats. I can find people saying that the wiring may be different on some models but I can't seem to get anyone to tell me how I can get the power seats to work. I don't want to buy the seats just to find out I can't get them...

I'm trying to find out if a 271 electric shift case can be converted to manual. I picked up a rolling chassis that has the manual shift lever but all that cases I track down are electric shift. I've read some stuff about people just swapping out the whole case. Then I see some stuff saying the...

Steed Speed T4 competition style for a 24v. Non gated. It was mocked up on an engine but never ran. $800 Located in Kingston, OH 45644

New PCS controller, harness, and valve body. I bought it to do a 48re swap in my 4th gen but have decided to stay with the 68rfe. I have around $2000 in it. Asking $1750 and a stock 48re valve body Located in Kingston, OH 45644

I was thinking about entering my truck in the show-n-shine. I've never entered anything like that so I have a couple questions. When do I need to be there? How much does it cost to enter? Do I need to enter my truck both days? Dumb questions, I know, but I'm clueless about these type of events.

I have a bare Extended Cab Long Bed 4wd 2nd gen Dodge frame sitting in the barn. I bought it for a spare but have decided that I don't need it any longer. I believe it is out of a 2000. It's in pretty good shape. Straight and only surface rust from sitting in a non heated barn. The only flaw...

Core 48re trans with a new in box Suncoast PCS controller. Will not separate because I exchanged the VB out of the 48 for the PCS. $2500