Recent content by jjrightmire1973

I have a radiator core support, Cowl Vent and the entire bel air / biscayne side trim moulding, they dont make these anymore. $500.00 OBO will consider trades

$250.00 OBO. would consider trades jjrightmire1973@yahoo.com

I wanna run my smarty on Timing number 2, right now I have it on 3. Anybody running windshield fluid and running smarty on 2? I dont wanna make a boat anchor outa this engine. thanks

I have an 03 HO with a 64-74-14 turbo, 90 HP II tips, II dual feed line, Arson III, AFE Blade runner, S&B intake, Valair 3600 DD,Springs and ARP studs, Devils Own Water meth with a 14,10 and 5 nozzels spraying windshield fluid. Spool-aid, Dr. Performance 2013 90hp chip stacked with smarty pod 06...

Just installed a Devil's Own kit with 3 nozzels installed: 14, 10, and 5. I have it come on about 18 PSI and full on at 30 ish. Just installed the kit and the calculator on Devil's Own web site said I needed about 35 GPH thats why I chose these three. Also it makes a sounds like air or ripping...

My II silver 62 S300 bit the dust last week after a rebuild, now the turbo shop wants to build any turbo I want using a new center section/cartridge. The turbo was a 2nd gen style II 62/74/14. I wanna keep the 14 and 74 but The shop told me I could get a 2.6 style or 64 CM or whatever I want. A...

I recently bought a devil's own water meth kit with the 250 PSI pump. I have 4 nozzels, a 4,5,10,14. Would tig welding bungs in the post intercooler pipeing work best? I have a AFE bladerunner intake and I dont think with the blades it would evenly distrubite the mixture, and being in the air...

I am going to replace the clutch in my diesel 3000 8 speed. I believe it has a double clutch. Is there a stronger clutch that will fit or work? I hear some clanking around in the bell housing and where is a good place to order one from. thanks

I am about to install a Devil's Own stage II water meth kit "as soon as I buy it" I am currently running My Smarty on TNT with SW7 tm-4 rp-2 and timing-2 and have it stacked with dr. performance stage 3 chip for pressure. I am worried that the Water meth kit will add too much timing and blowup...

I just got my Lucas CAV DPA pump rebuilt and turned up. How do I time the pump when I put it back on the Ford 3000 diesel tractor? I heard of something called drip timing but not really sure. Any help would be appreciated.

I am getting my injector pump rebuild and turned up a little, I think this engine is rated at 48 HP 3 cylinder. What small turbo would be good to use on this engine maybe make 5-10 PSI. I would like to maybe get 65 HP or so out of this tractor. And what other mods would help this little tractor...

I am looking to cap each injector to see which on is bad and not causing it to start. Where could I buy one and what is the part number. thanks

I replaced the batteries in my truck and got it started then the airdog let out a high pitched whine and 25 psi was the fuel pressure when normaly it is 17 psi then the pump stoped and I shut the truck down cause on 0 rail pressure. I blew the 20 amp fuse for the airdog so I replaced it and the...

My truck is a 2003 2500 HO I removed the smarty, the injectors are new and I alos put a new injector pump on the truck. I have 17 PSI to the injector pump also from the air dog 150.I thought is was the arson FCA so I switched it back with the stock one and it started but now the truck wont...

The dyno was a dyno dynamics doynmometer and I made 972 foot pounds of torque at 2410 rpms and 475 rwhp at 2640 rpms. My mods are dr. performance chip, smarty on level 9 with rail pressure on 4 and timing on 4, 90 hp injectors, silver 64 turbo, afe blade runner intake manifold and s & B intake...