Recent content by M249cummins

It is a 1982 Chevy truck. has a sbc 305, Headman longtube open headers, Edelbrock carb, MSD distributer, sm465 transmission, np205 gear driven transfercase, 14 bolt rear, 15x14 bart wheels, 35x14.5x15 tsl boggers a couple weeks old. lift is 6in? No frame rust no body rust. Underside of rockers...

I know its not diesel related but figured this was the best place for it. whats the best way to tell if a timing chain had got soo worn out that it has jumped a tooth or so? its on a 82 small block chevy. I run open headers in the truck so its hard to hear for noise. should turning the motor...

I have A1 12mm head studs and they are 2 different lengths. I just changed the head gasket and upon installation I totally forgot where the shorter studs went, any help please.

I'm in the process of changing my head gasket and noticed several of the head studs had a fair amount of crud on them by the thermostat and exhaust manifold and some decent rust on the threads. if I were to pull the threads out of the block would it be possible to put a 14mm stud in said...

why is it you don't see too many people run traction bars on the front? I have a 6in lift and got some pretty decent wrap and wondered why you never see bars on the front axle, why is that?

It is a 1989 W-150 rclb. It was built to be double triangulated with a scs dropbox, 2.5 tons with Big shocks coilovers and 44's. It is made from 2"x2" beveled 3/8 square tubing stick welded with 7018. it has a clean title still so it can be street legal if you wish. will come with 1 rear 2.5 ton...

I have a 12v IH cast block with 14mm mains from a 97 dodge 1 ton. comes with cam, 2 cranks, 2 sets of rockers, England rods, timing case, 12mm B&P industrial p7100 injection pump, power steering pump, starter, alternator, a/c compressor and a new loaded head. asking $500 or trade for a 4 bolt...

While pulling the head I noticed this thick scale buildup on 2 feed tubes and 2 injection line ends. All on the outside none inside. Will flake off with hard scraping, what could cause this? It’s not rust FYI.

started my truck up one morning heading to work and it started like it does when its cold out, did the whole lope chug deal for like 20 seconds but it was 55 out and a tone of blue smoke came out, soo thick you couldn't see through it, straight up fog machine, after a minute it idled fine so I...

looking to sell my new never used frozen boost type 17 Air/Water intercoolers. looking to get $400 **OBO** will sell individually if I have 2 buyers, ill pay shipping. ill get pictures up tomorrow.

My truck is a 99 ram 2500 CTD 4x4 and the driver side knuckle is wallered out where the tie rod goes into it. I have a complete earlier dana 60 with the unit bearing just like mine but was wondering if the tapered hole and everything else will bolt up. I want to say its a 96 or 97 dana 60 with...

I have 2 but only want to sell one of them. it came out of a 1962 m35a2 or m35a1. helped pull them out a few days ago. opened them up and still has oil in it, gears look great. asking $500 or trade for first gen dodge fenders, doors or bed, nv4500.

Picked up a marine p7100 pump off of Facebook for $300 and the guy knew nothing about it other than it was a marine application. The Id tag indicates it has 12mm plungers, normal rotation, p7xxx series. I believe it is a 919 pump. Does anybody know the "hp" rating of this pump? What's with the...

Thought I would post this just incase anybody was curious about it or had any questions. I started with a 1989 d150 2wd rclb with a 318ci Front end is from a 1997 dodge ram 2500 rclb 5.9 CTD Cuts look rough and the rust isn't perty but I smoothed it out and cleaned it up before I got welded.

I have 2 new air/water intercoolers from frozen boost type 17. Bought them for one of my projects but went another direction. New $600 from frozen boost, I'm asking $400 for both. Will not separate unless I have 2 buyers, I'll pay shipping:woohoo: 618-707-0225 anytime or pm me, thanks.