Search results

Have a complete 47rh that I had bought for a truck I was building but sold the project. This is a 2wd setup. Asking $800obo for all. I drove the truck the transmission came out of.

This motor came out of a bluebird and came from Scheid diesel. Ran the motor on the stand, oil pressure at idle is 60-65. We have a old 52 ford F1 truck. Dad and I were going to build a rat rod using a S10 chassis but when my wife got pregnant it got pushed a side. Have video of it running...

Doesn't matter what type of pump as long as it's not hot rodded. I have a pump from a bus and need a dodge application pump to make more power.

Do you guys put them in dry or some type of sealent?

I have a industiral motor and curious the piston difference? I confirm they have different piston by using Cummins Quickserve. If/when I go with bigger injectors I would like to know correct spray angle to get. Quickserve didn't have any info on the spray angle unfortunately.

Sounds odd I know. I'm building a hot rod using a cummins, open fender truck. I'm trying to gauge the area the intercooler and radiator will take up.ing to make a dumb radiator and intercooler for mocking up purposes. I'm also try Street truck that will have 350hp and maybe in the future as...

building a rat rod and would like to get some engine parts that can't be used.

How do you guys prime the oil pump? Just pour some oil in to the back side just to get the inside gears wet? I've read of using grease but would think that could cause a oil passage blockage.

Guys, I'm sorry to be blowing up this section of the forums. With my industrial motors (out of a bus) I'm looking to replace these two items for saftey as they are cheap. However I can find any specs on the dodge motors. The part numbers are different. The spring for the regulator and the...

Building to make 350hp. While I have the motor in the stand replacing items now. One of those are oil pump, motor runs strong and came out of a bus. While searching I came across that the updated 12v oil pump is what's on the 24 valves and it flow more oil. Didn't say how much but over all...

I don't mind pulling the cam to replace timing housing gasket but what I'm concern about is disturbing the headgasket from removing the rockers. I know that some guys pull the cam off and heat the gear up around 300 degrees. How successful is this approach? I understand that cummins does it...

Whats the difference between these two, other than one is for a auto (180hp)? What is someone use a 215 on a auto any negative effects?

I've been looking at these after a few friends experince with their 5.0 mustang (coycote motors) where they would pop due to a lean condition in the ECM programming and that rear cylinder being the hottest. I saw the fleece kit and while it's very nice, for what I'm doing it's out of price...

I have a industrial p pump motor for a build that is a 94'. I'm needing a oil drain because I'm swapping from a high mount to a dodge factory mount. I'm also needing oil feed because the current will not work with the dodge manifold. Cheap and reliable fits the bill. Also does anyone know...

Hey guys, got a new to me engine from a diesel performance shop that came out of a bus. Got it started last night and I had a little trouble clearing out the lines (first time ever doing this or having a cummins). Long story short during cranking the motor would puff white smoke out. When it...

As the title states. Not going for big power 300-350 tops. Don't have the funds for a billet but the truck is only 4,000 pounds. PRW are the only ones I've seen I didn't know if there were any others.

What would be a good pre-cleaner setup for a industrial 12 valve? Motor I've got coming in doesn't have this because it's located on a different area than on the motor.

I'm in need of a flexplate but the power I plan to run I do not need or have the funds for a billet 350+ dollar flexplate. I saw these on ebay. Didn't know if anyone had any experience with them. 47RE 47RH 48 RE 12V 24V SFI Flexplate to fit Cummins....NEW!! Dodge 2500 3500 | eBay

Need some good motor mounts. 3 or 4 bolt doesn't matter. Would like the bolts as well.

Hey, I'm in need of the following Need a tensioner fan pulley and bracket (no fan) Dodge alternator bracket and thermostat housing and neck