Search results

Hey guys the 3 pin triangle on the older and 3 pin weather pack is the J1939 data port correct? And isn't this the port that most tuners and boxes hook into correct? I'm not much for vp engines, just the old 12 valves. Lol Thanks for any info guys!

Hey guys, im going to be using a MD vp44 5.9 from a 2001 Freightliner school bus in a swap and have a few questions. Its a 205Hp model with a allison behind it. Can a guy just remove the allison and swap a manual behind it and not need a ECM reflash? Also can one have this engine Uprated to the...

Looking for a tuner for our 06 farm truck. Along the lines of a smarty or something. Let me know what ya got. Thanks

Looking for a used or new Hamilton cam for the wife's engine. 178/208 is the one we want, but want to do it on a tighter budget. So hoping to be a little cheaper than buying it directly from Hamilton. Thanks guys!

Looking for a nice deeper aftermarket trans pan for a 68rfe. Want to put it on a 545rfe. Looking for used. Let me know what ya got. Thanks

Got a guy looking for a 99-00 sd v10 manual trans with electronic tcase engine bay and trans/tcase harness. Let me know what ya guys got. Thanks

Looking for a set of nice early model aam 9.25 4.10 ring and pinion. Would also consider a newer set also. Thanks

Looking for a set of good used 20 over 01-02 h.o. pistons or 03-04 common rail pistons. Let me know what ya got guys! Thanks

Like the title says, looking for a rear yoke, bolt and washer for the 2wd g56 transmission. I'd even take the part number. Let me know what ya got guys! Thanks!

Im working on a 2001 RCSB f450 framed truck that has 01 f250 v10 wiring in it. looking for some pointers on the engine wiring aspect of the conversion. Going to be using a 6.0 alternator and the dodge a/c pump. Dodge throttle linkage on the pump along with the ford cruise. Truck has a nv4500...

Long story short, I Pissed up the seal robbing the motor off a new 150 I had on the shelf. Turns out the motor was fine anyway. But I looked at the seal and thought I could do better. Measured it up and ordered up a replacement dual lip SKF seal from McMaster Carr. Had it here the next day. And...

Ok guys got a problem. Borg s300 phatshaft from ii doesn't take the same bearings as a regular s300. Factory s300 o.d. on the bearings is .75". The ones I took out are around .81". Am I missing something or? Bought a severe duty rebuild kit and don't have the right bearings....

Looking for a set of VP lines complete with clamps. Thanks!

Just like the title says. Would need to have it before the end of the week, otherwise I'm hogging it out to the 12 valve square ports. One stud hole for the turbo has been fixed. Drilled out and a thread reducer put in. Works great! Let me know what ya got! Would sell for the right price!

What are you guys using for thread size in the 5.9's oil galley and coolant plugs in the block? Behind the tappet cover, behind the front cover and trans plate. Front and rear I believe 1/2" pipe will work but curious if I should drill the others out to fit a pipe thread or? Thanks for the info...

Just like the title says. Looking for a nice set of 04.5 and up standard common rail pistons. Let me know what ya got. Thanks

I have a brand new set of DAP pushrods for a 24 valve. Looking to get $180 shipped for them. New in box. Going 12 valve so I dont need them. Thanks CompD!!

I got a stock unmolested AFC housing off a 190 HP bus pump. Same as the dodge pumps. Still has tamper proof screws in it. Based on other housing prices I would like to get $100 bucks shipped.

I've got a gta4294 for sale. iirc its 67/82/1.15 I bought if from a local buddy of mine and rebuilt it to use on my tractor but using my hx52 instead. Cast wheel. The exhaust housing has some heat cracks inside but none on the outside. No run time since rebuild. Id like to get $500 bucks for...

i want a junk s400 cover to cut the v-band flange off the outlet to weld to a different turbo. thanks Tyler