Search results

24 "Top Hat" style exhaust seals. In the packaging. Cummins P/N 3955394 $40 shipped OBO 12/12 Intake & Exhaust Cummins set of the conventional style seals $30 shipped OBO

Rods out of my '02 engine. They've been checked and straight and center to center within spec. Ready to be shot penned and polished. $125 shipped.

Used cam retainer plate. It was in for about 5k miles until I went to a SMT adjustable cam gear and used the one they provided. $35 shipped OBO

Don't know if these pistons could be of use for anyone for a 4BT or not. They were .020" Cummins 24v pistons that had .040" valve reliefs cut and coated by PolyDyn, Tops & skirts This engine wanted to be a 4Cyl so bad it gave 5 & 6 the boot. Lol The others are fine and the coating still looks...

6 Cummins Cam Bearings P/N 3940059 O.D. 2.335" .100" thick Coated by PolyDyn $100 shipped OBO

Bypass Valve w/mounting bracket and rear plate from EatSoot.com Bypass was never used just sitting around. The plate was bolted to the block to mock up some braided stainless lines but I used a different setup since then. I have a new o-ring that'll come with it. $175 shipped for both. PayPal...

I'm needing to pull the 3 side plugs and rear plate that I purchased from you a while back for my '02 24v and would like to buy new O-rings for when I replace them. Can you quote me a price for them or if they are a standard item that I can buy locally I could do that. Thanks Ben.

https://www.youtube.com/watch?v=zsetV5Z-Mqc Maybe this will be a ongoing TV coverage for events like TS and SDX.

Jeff, Will this work to replace the filter housing for someone that has a Dual Remote AMS Oil kit? The 2 smaller holes are for turbo oil feeds correct? Does it have the relief/bypass internally? Thanks

T$, can you break down in a post with pictures of the available individual options you have. In the S300 & 400 size turbos. The different Comp covers: 3rd gen, 2nd gen, race covers. The different available Comp wheels: 62/63/64/66 cast and billet. The standard and upgraded thrust bearing...

Jeff, Can I get a single .010" rod bearing??? Assembling this engine and it is out of round. I don't know if it happened while it was getting coated or what. If you don't see this ill call ya by Friday. Thanks Ben

Need a "100" plate for a p7100 pump. I've lost the plate I had someplace and can't find it. I gues that's what I get for taking it out! lol Thanks

Needing 2nd gen comp cover for 63/68 s300 pn 177283 Thanks

Needing to get a 2nd gen style cover for my 63/68 s300 pn 177283. Post or pm me pricing if available. Thanks

Needing to get a 2nd gen style cover for my 63/68 s300 pn 177283. Post or pm me pricing if available. Thanks

Looking to buy opies bypass but only the block and bracket. No hoses or fittings needed. Thanks

When using boreable pin bushings for a 12v rod what is the acceptable limit to bore off center to raise the piston up for a little more compression. Dead center bushing, the piston is .013 out of the hole. Would it be safe to bore .010- .015 off center to get the piston .023-.028 out?? If...

Complete Dana 60 & 70 out of a 2001. Factory Anti-slip 4:10 gears. Truck had 98k this is a disk brake D70. Axles located in Dayton Ohio. Local pickup unless you set up shipping at the local shipper. 800 OBO.

Borgwarner turbo 171702 Good bottom charger in compound set up. 1.32 a/r T6 $750 shipped It's never been out of the box just sitting here I was going to use it in a compound for the tow pig but went another direction. I can take paypal

.084 lines and clamps. Mild steel Never had any fuel through them. $400 OBO Any intrest please post on the thread instead of sending pm's.