1st gen cummins rclb built auto

Zeppelin654

New member
Joined
Nov 11, 2011
Messages
843
1992 W250. 215,000 on the body, and 175,000 on the motor. Everything else has 1000 miles on it.

There is very minimal rust on it. Just two spots on the sides of the fenders. Rockers and underbody are perfect.

I replaced all of the brake system besides the booster:

calipers
rotors
pads
hand bent lines
master cylinder
all rubber lines
drums
springs for drums
shoes
e brake cables (all 3)
abs sensor
amsoil fluid
bearings
etc

new Suspension and steering parts:

new tie rod ends
alignment
steering stabilizer
red head steering box
borgeson high flow power steering fluid pump
vacuum pump seals
borgeson u joint style HD steering shaft
skyjacker soft ride 2.5" leaf springs in the front
bilstein 5100 shocks all around
heavy duty receiver hitch (recessed) with rigid industries led reverse light (hidden)
new vacuum hoses
amsoil power steering fluid

Engine and fuel parts:

all brand new 1/2" hoses
Hellman fuel sump
Fass 220 gph adjustable lift pump
donaldson water separator and fuel filter
dual feed to the 160 ppump
tork tek 060 hp overflow banjo (pressure never drops below 50 psi)
mack rack plug
power driven 7mm dv's
infinite performance 5x.016's 155* (weston's injectors and recommendation)
stock lines
no plate
AFC live
60 lb valve springs
4k gsk
billet tappet cover
billet stock lift pump block off plate
22* timing
PDR 5 layer 150 psi intercooler boots
2nd gen intercooler and radiator
KDP tabbed
new front crank seal and new rear main seal
fumoto drain valve
Borg Warner SX-E 64.5/73/.91 T4
Steed Speed T4 manifold with stainless bolts
4" full exhaust
ss oil feed line and new oil drain
donaldson elf7349 oil filter and brad penn 15w-40 diesel oil has been used
amsoil coolant

Driveline/transmission parts:

mag hytec rear dana 70 pan
amsoil severe gear fluid
dana 60 front end with lockable hubs
all new u joints
sfi rated flex plate
DPC billet triple disc convertor

4x4 47RH trans with:

tcs billet input shaft
tcs standard billet intermediate shaft
pcs billet parts (band, strut, acumulator and servo)
direct power pack from firepunk diesel (5 friction setup)
trans go full manual valve body constant pressure
2nd gear servo return spring from goerend
deep aluminum pan (temps never saw over 170)
48RE overdrive planetary set
5 pinion steel main planet upgrade

Castrol Dex III fluid in trans and t case

O/D and Lockup switches

NP205 transfer case

B&M pro ratchet stealth shifter
BD diesel remote trans cooler with fan (on switch) (in the bed of truck) 1/2" lines

Moto Metal 962 wheels 20x12 with 33" mickey thompson atz's (90% tread left)
Metal Lugz black spiked lug nuts
Extang tonneau cover

Isspro gauges:

fuel pressure
fuel level (new isspro sender too)
boost
pyro
trans temp
tach

New pioneer sound system with JL Audio 10" sub behind seat

Interior is excellent (minus headliner)

Truck Lite LED dot legal headlights



Now for the bad. I sent in an oil analysis report and here are the results. I see no coolant in the oil though. Dipstick looks perfect, as does oil fill cap. No oil in coolant. Truck runs awesome, so it beats me.

13557939_10153942329839064_7659085708331306125_n.jpg



I am asking $10,000 for the truck and $13,000 for ALL of the spare parts including engine parts, blocks, head, crank, pump, etc

A stock 47RH will go with it, as well as a new 12v standard bore block, a 12v short block, 12v head thats almost new and has titanium keepers and retainers + 60 lb springs, new balanced crank, coated non i/c pistons, balanced england rods, waterman lift pump, billet front cover, extra ppump injection pump, the list goes on...

Please call me or text me with any questions or more pictures (I have a bunch) at 814-460-3465. My name is Devin. Truck is located in Clearfield, PA 16830. Thank you

12790883_10153638751404064_1633936111841907581_n.jpg


1618557_10153638751509064_5668814569764842111_n.jpg


22196365_10155372326534064_5626527290531416913_n.jpg


12734214_10153638751599064_1926168549814214378_n.jpg


Thank you
 
How do you like that shifter with the extension?

I like this truck a lot, maybe I’ll send the link to a buddy up north so I can live vicariously through him.
 
I like it a lot. It works perfectly and it’s fun to hit it/slap it when you’re goin through the gears. I extended it about two feet because I don’t like the ones that are mounted on the pedestals and this way, the cable is hidden instead of hanging way out. Plus, my other truck is a 4th gen that’s a stick shift and I made that shifter higher too, so I wanted it to be similar.
 
Interested in B&M pro ratchet stealth shifter
BD diesel remote trans cooler with fan (on switch) (in the bed of truck) 1/2" lines if available.
 
That went with the truck. My other thread has the parts listed that are still available
 
Back
Top