DarrenKrueger
STRAIGHT SIX SLED PULLER
- Joined
- Jan 28, 2008
- Messages
- 303
Calhoun County Fair Pull
saturday the 8th starts at 6:30, hopeing for a good turnout
Not sure on the 3.0 rules i will post as soon as i find out,
-2.6 Class (8,000 lbs)-
$1900 Paying 5 places
1. Front hanging weights are allowed, not to exceed 60 inches forward of the center of the front axle. Will be measured from center of front wheels to end of weight assembly. If weight is added to the bed it MUST be mounted and secured.
2. Four wheel hydraulic brakes are mandatory.
3. OEM chassis is mandatory.
4. Radiators must be in the stock location and be of at least stock size.
5. OEM transmission and transfer case are mandatory. Must have been an option in one ton or smaller pickup.
12. Rear Ends must have been in a 1 ton or smaller pick up.
13. Front and Rear Traction Bars are Allowed.
14. Blocked suspension allowed.
6. OEM restraint system is mandatory and must be worn.
7. Must have rear drive shaft loops. If front u-joint is visible, it must have one there as well
8. Engine and transmission can be interchanged between Dodge, Ford, and GM as long as they came in a 1 ton truck or less from the factory.
9. Must have two 3/8 inch diameter bolts placed through the exhaust pipe in a cross pattern one inch of the other. Also must be within 12" of the turbo.
10. Exhaust is preferred to be directed upward (safety) but is not mandatory.
10. Fuel Injection Pumps must be stock appearing. The use of multiple high pressure common rail CP3's is legal. Powerstrokes may utilize a 2nd HPOP. Ag governor p-pumps are allowed.
11. Nitrous and Propane are Prohibited.
15. DOT street tires. Cut tires are prohibited. Duals allowed. 35" max tire size.
16. Bell housing blankets are RECOMMENDED.
17. The vehicle is limited to a 2.6 inducer bore single turbocharger. The inlet will be measured using a 2.65 inch plug and it must not be able to enter the inducer bore. Bushing must be within 1" of wheel. The vehicle driver will be responsible for making compressor wheel accessible for tech official(s) to measure bore and be able to inspect compressor wheel. 6.4 Fords can run factory appearing compounds.
18. Water injection systems are allowed.
19. Air to water intercoolers are allowed.
20. The vehicle must retain the original factory wheelbase and track width.
21. Hitch must be receiver style (Reese). Bracing is allowed but nothing passed the center line of the axle. No part connected to axle (no trick hitch). Hook point must be a minimum of 44'' behind center line of axle. Max height of 26'' for 4 wheel drive, 30'' for 2 wheel drive. Should be adjustable.
22. No adjustments allowed in the pit once the truck passes tech inspection/weigh-in. If it is suspected that a driver has done so, it will have to pass tech again before pulling. NO EXCEPTIONS
saturday the 8th starts at 6:30, hopeing for a good turnout
Not sure on the 3.0 rules i will post as soon as i find out,
-2.6 Class (8,000 lbs)-
$1900 Paying 5 places
1. Front hanging weights are allowed, not to exceed 60 inches forward of the center of the front axle. Will be measured from center of front wheels to end of weight assembly. If weight is added to the bed it MUST be mounted and secured.
2. Four wheel hydraulic brakes are mandatory.
3. OEM chassis is mandatory.
4. Radiators must be in the stock location and be of at least stock size.
5. OEM transmission and transfer case are mandatory. Must have been an option in one ton or smaller pickup.
12. Rear Ends must have been in a 1 ton or smaller pick up.
13. Front and Rear Traction Bars are Allowed.
14. Blocked suspension allowed.
6. OEM restraint system is mandatory and must be worn.
7. Must have rear drive shaft loops. If front u-joint is visible, it must have one there as well
8. Engine and transmission can be interchanged between Dodge, Ford, and GM as long as they came in a 1 ton truck or less from the factory.
9. Must have two 3/8 inch diameter bolts placed through the exhaust pipe in a cross pattern one inch of the other. Also must be within 12" of the turbo.
10. Exhaust is preferred to be directed upward (safety) but is not mandatory.
10. Fuel Injection Pumps must be stock appearing. The use of multiple high pressure common rail CP3's is legal. Powerstrokes may utilize a 2nd HPOP. Ag governor p-pumps are allowed.
11. Nitrous and Propane are Prohibited.
15. DOT street tires. Cut tires are prohibited. Duals allowed. 35" max tire size.
16. Bell housing blankets are RECOMMENDED.
17. The vehicle is limited to a 2.6 inducer bore single turbocharger. The inlet will be measured using a 2.65 inch plug and it must not be able to enter the inducer bore. Bushing must be within 1" of wheel. The vehicle driver will be responsible for making compressor wheel accessible for tech official(s) to measure bore and be able to inspect compressor wheel. 6.4 Fords can run factory appearing compounds.
18. Water injection systems are allowed.
19. Air to water intercoolers are allowed.
20. The vehicle must retain the original factory wheelbase and track width.
21. Hitch must be receiver style (Reese). Bracing is allowed but nothing passed the center line of the axle. No part connected to axle (no trick hitch). Hook point must be a minimum of 44'' behind center line of axle. Max height of 26'' for 4 wheel drive, 30'' for 2 wheel drive. Should be adjustable.
22. No adjustments allowed in the pit once the truck passes tech inspection/weigh-in. If it is suspected that a driver has done so, it will have to pass tech again before pulling. NO EXCEPTIONS
