pierce460
Beave Wrangler
- Joined
- Apr 1, 2010
- Messages
- 611
July 29th Will be WS,2.6,Open. This will be after the fair ITPA pull. Pull starts at 6.
July 30th Will be WS,2.6,Open. This will be after the antique tractors. Pull starts at 5. $150 for WS $150 for 2.6 and $200 for Open.
Email or PM me with any questions. nteryan@joink.com
2.5 Work stock rulesWeight: 8000lbs. weight with driver included.
Ballast: Ballast is permitted. Front hanging weights are prohibited. Ballast may be added to the bed of truck.
Turbocharger: The turbocharger is limited to a direct bolt on. T4 foot limit. With an inducer bore of 2.5 limit,with 1/8'' protrusion. measured with a 2.55 plug with zero tolerance. 6.4 liter powerstroke engines may utilize the factory compound-turbo configuration.The driver will be responsible for making compressor wheel and bore accessible for tech personnel to measure bore and inspect compressor wheel.
Fuel Injection Pump: The fuel injection pump is limited to a stock-appearing, OEM engine make-specific pump only. The use of multiple high-pressure common-rail fuel pumps is prohibited. Pumps from different years in the same engine model may be interchanged
Water Injection: Water injection is prohibited. All system components must be removed from truck. Nitrous Oxide is prohibited.
Street Equipment: Complete headlight and taillight assemblies (all) are mandatory and must be operative. Complete OEM windshields and windows are mandatory.
Exhaust: No hood or fender stacks.
2.6 Diesel rulesWeight : 8000 lb Maximum, with driver
Ballast:Ballast is permitted. Front hanging weights are permitted. May not extend more than 60 inches from the centerline of the front axle.
Turbocharger:The vehicle is limited to a single 2.6 inlet turbocharger. The compressor wheel must
protrude into the compressor inlet bore 1/8 inch. The inducer bore is non-removable and must be maintained for ¾ of an inch from the front face of the compressor wheel. The inlet will be measured with a 2.65 plug, or internal calipers. No MWE groove width greater than (.200) of an inch will be allowed. The entire MWE groove must be placed behind the cut or step on the wheel for the protrusion into the inducer bore. The driver will be responsible for making compressor wheel and bore accessible for tech personnel to measure bore and inspect compressor wheel.
Fuel Injection Pump:The fuel injection pump is limited to cylinder number specific ( I.e. 6 cylinder pump on a 6 cylinder motor). Dual high pressure common rail fuel pumps are permitted. Ag governors are allowed.
Exhaust:All vehicles must be equipped to direct exhaust upward. The exhaust must exit rearward of the driver’s compartment or through the hood.
Intercoolers:Factory style or aftermarket intercoolers are allowed. Water to air intercoolers allowed. Ice and water must be weighed at the time of crossing the scales
Water Injection:Water injection is prohibited. All system components must be removed from truck.
Open DieselWeight : 8000 lb Maximum, with driver. Run what you brung.
July 30th Will be WS,2.6,Open. This will be after the antique tractors. Pull starts at 5. $150 for WS $150 for 2.6 and $200 for Open.
Email or PM me with any questions. nteryan@joink.com
2.5 Work stock rulesWeight: 8000lbs. weight with driver included.
Ballast: Ballast is permitted. Front hanging weights are prohibited. Ballast may be added to the bed of truck.
Turbocharger: The turbocharger is limited to a direct bolt on. T4 foot limit. With an inducer bore of 2.5 limit,with 1/8'' protrusion. measured with a 2.55 plug with zero tolerance. 6.4 liter powerstroke engines may utilize the factory compound-turbo configuration.The driver will be responsible for making compressor wheel and bore accessible for tech personnel to measure bore and inspect compressor wheel.
Fuel Injection Pump: The fuel injection pump is limited to a stock-appearing, OEM engine make-specific pump only. The use of multiple high-pressure common-rail fuel pumps is prohibited. Pumps from different years in the same engine model may be interchanged
Water Injection: Water injection is prohibited. All system components must be removed from truck. Nitrous Oxide is prohibited.
Street Equipment: Complete headlight and taillight assemblies (all) are mandatory and must be operative. Complete OEM windshields and windows are mandatory.
Exhaust: No hood or fender stacks.
2.6 Diesel rulesWeight : 8000 lb Maximum, with driver
Ballast:Ballast is permitted. Front hanging weights are permitted. May not extend more than 60 inches from the centerline of the front axle.
Turbocharger:The vehicle is limited to a single 2.6 inlet turbocharger. The compressor wheel must
protrude into the compressor inlet bore 1/8 inch. The inducer bore is non-removable and must be maintained for ¾ of an inch from the front face of the compressor wheel. The inlet will be measured with a 2.65 plug, or internal calipers. No MWE groove width greater than (.200) of an inch will be allowed. The entire MWE groove must be placed behind the cut or step on the wheel for the protrusion into the inducer bore. The driver will be responsible for making compressor wheel and bore accessible for tech personnel to measure bore and inspect compressor wheel.
Fuel Injection Pump:The fuel injection pump is limited to cylinder number specific ( I.e. 6 cylinder pump on a 6 cylinder motor). Dual high pressure common rail fuel pumps are permitted. Ag governors are allowed.
Exhaust:All vehicles must be equipped to direct exhaust upward. The exhaust must exit rearward of the driver’s compartment or through the hood.
Intercoolers:Factory style or aftermarket intercoolers are allowed. Water to air intercoolers allowed. Ice and water must be weighed at the time of crossing the scales
Water Injection:Water injection is prohibited. All system components must be removed from truck.
Open DieselWeight : 8000 lb Maximum, with driver. Run what you brung.
