SuperSonic
El Vato
- Joined
- May 31, 2006
- Messages
- 2,036
Here is the motherload.
This is all the stuff i've been saving for my "projects".
I have
- A Cyclone Sandblast Cabinet 30"x30" with vac system. Used very little, in VGC. $250.00
- Multiquip 6000 generator, honda engine, low hours, kept inside, serviced regularly. $450.00
- 3 used RG "Vantage" infared tube heaters 100k BTU Nat Gas. used for 4mos in a quick lube. VGC, tubes and shields are not included, they were setup for up to 40ft of tube. tubes are easy to make from 4" exhaust tube. $150.00 each.
- 3 NIB RG VantageII infared tube heaters 120k BTU. i bought six of these @ $600.00 ea and put three up initially.
Three is enough to run us out of our 65x85x16 shop in about 20Min. $450.00 each
- 3 Deutz engines I bought to use for a saw repower. They are 3cyl turbo diesels rated @63hp. Liquid (oil) cooled, with self contained cooling pack. One is a parts engine that has 2 good rods and pistons, a good head, cooling system, turbo, fuel system and misc. One has low hrs. >300. and runs. and the last is nearly new @ 150.hrs but had a bad turbo form the factory, runs great. these would work for an economy car repower, concrete saw, portable sawmill, tractor, generator etc.I'll take $500.00 for the parts engine, $1,700.00 for the one with low hrs. And $1,900.00 for the newer one. or $3,700.00 for all three.
- GreenLee professional tubing/pipe bender. will do up to 3" pipe Comes with a bunch of pieces. pump, metal box, etc. used very little. $1200.00 (nearly 2000.00 new and they dont make 'em like they used to)
- Hobart BetaMig 200 Mig welder in VGc w/ new cord, new lead and handle, new electronics. $750.00
- 1 set of Longacre ComputerScales model # 7258 in VGC, You can use these digital scales fro anything from .5-10,000 lbs they were just sent back and recalibrated. They are great for racing and pulling vechiles or if your MIL is real big. $400.00
- 05 Cummins CR engine from a rollover with 40k on it. Sat w/o a hood for a while so we pulled it down. there are a few very light rust pits at the very top of the #4 cyl (10 over will clean it up easy) We have the complete engine less the fuel system, sensors, ECM, Harness, balancer, valve cover water pump, intake horn and turbo. I can sell it as is for $2800.00. or bore it, and put new pistons in it for $4500.00 (basically a new longblock). Or I can custom build it to your specs and sell it as a "drop in" race engine.
- 2 Cummins 24v engines. one is a 99 w/53k and the other is a 01 w/38k. Both are victims of the 53block issue, neither have an inj. pump. both have good heads, pistons, rods, cams, most if not all sensors. etc. One has a hole in the oil pan from another engine. $1,200.00 for the 01 w/good pan, and $1,000.00 for the 99.
- 98 Cummins 12v 215 w/120k has 60lb ex. valve springs, newer water pump, new balancer, 300 injectors. Marine HG. Does not have inj. pump, valve covers, PS pump, or turbo. $2,300.00
- New Ag. race block. Std. bore, decked, fire ringed, needled cam journals, setup for roller lifters, setup for 14mm head studs, includes HD mains and 14mm main studs, hard blocked, perf coating, bronze lifter guides, oiling mods. clearenced for Arias pistons w/ keystone rings. All machine work done by Schied Diesel service. over $6,300 new. $5,500.00
- Billet 12v cam with tappetts, SS push tubes, race valve springs, Titainium keepers and retainers, stainless in. and inconell ex. valves. complete valvetrain less rockers. cam is from Enterprise Engine and was used for approx. 4 runs before we went to a roller setup. moves some serious air. $1,500.00 for everything. basic specs available TO THE BUYER!
- Used 12v RV cam low miles $250.00
- 1 Set of std. bore CR pistons out of an 05 w/40k. $650.00
- Bosch P-7100 "913" 215Hp injector pump, w/ 79k mi. Needs rebuilt (P&B's). truck had a bad batch of fuel. $600.00
- 1 set of Arias 10.5-1 pistons for a 12v cummins Std. bore. setup for straight cut rings, In good condition (10-12 runs). $800.00
- 1 set of 12v Cummins stock 215hp pistons. std. bore in VGC >15k mi. $200.00
- 1 set of Stock 2001 24v Connecting rods. came out of stock engine w/ 24k mi. $350.00
- 1 set of new 60lb. 12v performance valve springs. $100.00
- 05 Dodge CR fuel rail w/lines. $100.00
- Dana 60F 4.10-1 ring & pinion > 20k mi. I swapped to 3.73's in my flatbed, never pulled with these gears. LIKE NEW. $50.00
- Used HX-35 approx 60k mi. wastegated to 38lbs. has a 12cm housing but needs new t- housing as the threads pulled when dissassembled. $200.00
- 01 Dodge Auto trans cooler, like new. $100.00
- 01 Dodge Flex plate, like new. $120.00
- 01 Dodge trans adapter. $200.00
- New 4" SS silverline 2nd gen down pipe for HX-35. $50.00
- Dodge Dana 60 Drivers side axle. $100.00
- Modified Cummins tappet cover w/ 2 1" barbed ports for extra breathing. $50.00
- New 12v intake cover with grid heaters. $100.00
- 1 set of HD main caps from an AG block. $50.00
- 02-04 ford SD Drivers side headlight and turn signal. like new. $75.00
- Set of std. ford SD power mirrors lt. scuff on front of the drivers side. perfect for if your going to paint them, glass is perfect. $50.00
- 02 Ford SD diesel guage cluster. shows 218k mi. $25.00
- NIB amber driving lights (rectangular) w/ black cover/guard. with wiring kit and switch. $50.00
- Putco SS "Flames" grill inserts for 94-02 Dodge ram. in VGC. $40.00
- KAZ Adventure Buggy. 125cc 4 stroke. independent ft suspension & swing arm rear supension, adj. coilovers, very low hrs/mi. new rear axle, good tires
good paint, runs great, very fast. $400.00
All items sold as is
I will charge actuall shipping via UPS FedEx or DHL .
I can deliver any of the larger items to anywhere within 500 miles from 45103.
Pictures of any item is available upon request.
I require cash, money order, or cashiers check.
I can be reached here, at watson_contracting@yahoo.c o m, or by phone @ 513-919-3411
Thanks.
This is all the stuff i've been saving for my "projects".
I have
- A Cyclone Sandblast Cabinet 30"x30" with vac system. Used very little, in VGC. $250.00
- Multiquip 6000 generator, honda engine, low hours, kept inside, serviced regularly. $450.00
- 3 used RG "Vantage" infared tube heaters 100k BTU Nat Gas. used for 4mos in a quick lube. VGC, tubes and shields are not included, they were setup for up to 40ft of tube. tubes are easy to make from 4" exhaust tube. $150.00 each.
- 3 NIB RG VantageII infared tube heaters 120k BTU. i bought six of these @ $600.00 ea and put three up initially.
Three is enough to run us out of our 65x85x16 shop in about 20Min. $450.00 each
- 3 Deutz engines I bought to use for a saw repower. They are 3cyl turbo diesels rated @63hp. Liquid (oil) cooled, with self contained cooling pack. One is a parts engine that has 2 good rods and pistons, a good head, cooling system, turbo, fuel system and misc. One has low hrs. >300. and runs. and the last is nearly new @ 150.hrs but had a bad turbo form the factory, runs great. these would work for an economy car repower, concrete saw, portable sawmill, tractor, generator etc.I'll take $500.00 for the parts engine, $1,700.00 for the one with low hrs. And $1,900.00 for the newer one. or $3,700.00 for all three.
- GreenLee professional tubing/pipe bender. will do up to 3" pipe Comes with a bunch of pieces. pump, metal box, etc. used very little. $1200.00 (nearly 2000.00 new and they dont make 'em like they used to)
- Hobart BetaMig 200 Mig welder in VGc w/ new cord, new lead and handle, new electronics. $750.00
- 1 set of Longacre ComputerScales model # 7258 in VGC, You can use these digital scales fro anything from .5-10,000 lbs they were just sent back and recalibrated. They are great for racing and pulling vechiles or if your MIL is real big. $400.00
- 05 Cummins CR engine from a rollover with 40k on it. Sat w/o a hood for a while so we pulled it down. there are a few very light rust pits at the very top of the #4 cyl (10 over will clean it up easy) We have the complete engine less the fuel system, sensors, ECM, Harness, balancer, valve cover water pump, intake horn and turbo. I can sell it as is for $2800.00. or bore it, and put new pistons in it for $4500.00 (basically a new longblock). Or I can custom build it to your specs and sell it as a "drop in" race engine.
- 2 Cummins 24v engines. one is a 99 w/53k and the other is a 01 w/38k. Both are victims of the 53block issue, neither have an inj. pump. both have good heads, pistons, rods, cams, most if not all sensors. etc. One has a hole in the oil pan from another engine. $1,200.00 for the 01 w/good pan, and $1,000.00 for the 99.
- 98 Cummins 12v 215 w/120k has 60lb ex. valve springs, newer water pump, new balancer, 300 injectors. Marine HG. Does not have inj. pump, valve covers, PS pump, or turbo. $2,300.00
- New Ag. race block. Std. bore, decked, fire ringed, needled cam journals, setup for roller lifters, setup for 14mm head studs, includes HD mains and 14mm main studs, hard blocked, perf coating, bronze lifter guides, oiling mods. clearenced for Arias pistons w/ keystone rings. All machine work done by Schied Diesel service. over $6,300 new. $5,500.00
- Billet 12v cam with tappetts, SS push tubes, race valve springs, Titainium keepers and retainers, stainless in. and inconell ex. valves. complete valvetrain less rockers. cam is from Enterprise Engine and was used for approx. 4 runs before we went to a roller setup. moves some serious air. $1,500.00 for everything. basic specs available TO THE BUYER!
- Used 12v RV cam low miles $250.00
- 1 Set of std. bore CR pistons out of an 05 w/40k. $650.00
- Bosch P-7100 "913" 215Hp injector pump, w/ 79k mi. Needs rebuilt (P&B's). truck had a bad batch of fuel. $600.00
- 1 set of Arias 10.5-1 pistons for a 12v cummins Std. bore. setup for straight cut rings, In good condition (10-12 runs). $800.00
- 1 set of 12v Cummins stock 215hp pistons. std. bore in VGC >15k mi. $200.00
- 1 set of Stock 2001 24v Connecting rods. came out of stock engine w/ 24k mi. $350.00
- 1 set of new 60lb. 12v performance valve springs. $100.00
- 05 Dodge CR fuel rail w/lines. $100.00
- Dana 60F 4.10-1 ring & pinion > 20k mi. I swapped to 3.73's in my flatbed, never pulled with these gears. LIKE NEW. $50.00
- Used HX-35 approx 60k mi. wastegated to 38lbs. has a 12cm housing but needs new t- housing as the threads pulled when dissassembled. $200.00
- 01 Dodge Auto trans cooler, like new. $100.00
- 01 Dodge Flex plate, like new. $120.00
- 01 Dodge trans adapter. $200.00
- New 4" SS silverline 2nd gen down pipe for HX-35. $50.00
- Dodge Dana 60 Drivers side axle. $100.00
- Modified Cummins tappet cover w/ 2 1" barbed ports for extra breathing. $50.00
- New 12v intake cover with grid heaters. $100.00
- 1 set of HD main caps from an AG block. $50.00
- 02-04 ford SD Drivers side headlight and turn signal. like new. $75.00
- Set of std. ford SD power mirrors lt. scuff on front of the drivers side. perfect for if your going to paint them, glass is perfect. $50.00
- 02 Ford SD diesel guage cluster. shows 218k mi. $25.00
- NIB amber driving lights (rectangular) w/ black cover/guard. with wiring kit and switch. $50.00
- Putco SS "Flames" grill inserts for 94-02 Dodge ram. in VGC. $40.00
- KAZ Adventure Buggy. 125cc 4 stroke. independent ft suspension & swing arm rear supension, adj. coilovers, very low hrs/mi. new rear axle, good tires
good paint, runs great, very fast. $400.00
All items sold as is
I will charge actuall shipping via UPS FedEx or DHL .
I can deliver any of the larger items to anywhere within 500 miles from 45103.
Pictures of any item is available upon request.
I require cash, money order, or cashiers check.
I can be reached here, at watson_contracting@yahoo.c o m, or by phone @ 513-919-3411
Thanks.
