5.9 Commonrail parts list

Mark Nixon

No Savior among the flesh
Joined
Feb 26, 2009
Messages
8,678
Standard bore block, needs bored/sleeved, $350, plus freight.

Standard crank, needs cut .010-.010, not scorched on any journals, $250, plus freight.

Cylinder heads, 5.9s or 6.7s, no cracks that I can see, $400 each, plus freight.

CP3s, have several, $175 each.

Injector CORES, mostly 2004.5-2007, $40 each.

2006-2007 5.9 valve covers, $100 each.

2006-2018 rocker boxes, $45 each.

2006-2007 AUTOMATIC transmission cooler lines, from the lower outlet to the rear trans cooler inlet, $100/set

Oil cooler cover/filter head, $40 each.

4wd engine mount brackets, one left and one right side, $65/pair.

Pressed tip rocker arms (no plastic retainer) for 5.9 or 6.7, $120/set.

Block adapter plate, fits automatic from 2003-2007, or G-56 from 2005-2015, $125.

Complete 2006 longblock 5.9, has blowby, no turbo, CP3, or injectors, $1250, with injectors and CP3, $1500, plus freight.

2003 engine from ahead of an NV5600, good running condition, no accessories such as alternator, starter, A/C compressor, ecm or harnesses, $3000, plus freight.

Also have other miscellaneous 5.9 and 6.7 parts available.

Reply, PM, Call or Text 402-780-5127
 
Last edited:
I meant to mention that anything NOT marked "plus freight/shipping" is FREE SHIPPING.

Lots of good parts here that's just going to get tossed in the scrapper, or go to the core buyers.
Hate to waste it, but eating is eating and iron, aluminum and plastic doesn't chew well, nor does it taste very good. LOL

Mark.
 
I also have about 30 Cummins 5.9 and 6.7 CP3 pump gears.
I'll take $20 SHIPPED for one, OR $15 SHIPPED each, for 2 or more.

Mark.
 
None off and I have a few scrap cranks.
Just need to figure out a way to pull them.

Mark.
 
None off and I have a few scrap cranks.
Just need to figure out a way to pull them.

Mark.



I picked up a 12 ton hydraulic puller from harbor freight to pull one of these gears off of a junk crank. Worked very well.
 
I picked up a 12 ton hydraulic puller from harbor freight to pull one of these gears off of a junk crank. Worked very well.
I'll look into that. Got a part/stock number?
Seems like I can sell just about any crank gear, if I have them off.

Mark.
 
Updated list:

2005, 130,000 mile, 5.9 standard bore bare block, with pistons.
It turned a bearing on #4, otherwise bores are nice, 1 piston just touched and has light marks on the top, but should be okay, or I have another piston.
Block with pistons, no rods, $550 plus freight.

Crank from above, needs cut .010-010, $200.

2 or 3 odd 5.9 blocks, all need bored or sleeved in some fashion, $300/obo each, plus freight.

Cylinder heads, 5.9s or 6.7s, no cracks that I can see, $400 each, plus freight.

CP3s, have several, $175 each SHIPPED.

Injector CORES, mostly 2004.5-2007, $50 each SHIPPED.

2006-2007 5.9 valve cover, $100 SHIPPED.

2006-2018 rocker box, $50 SHIPPED.

2003-2005 valve covers, no top bonnet, $60 SHIPPED.

2003-2005 rocker box, with harnesses, $65 SHIPPED.

5.9 oil pans, no tubes, might need a dinger or 2 worked out, no rusty or crushed junk, $100 SHIPPED.

Oil pick up tubes, most need a thorough cleaning, no dents, straight screens, $65 SHIPPED.

Oil cooler cover/filter head, $50 each SHIPPED.

4wd engine mount brackets, one left and one right side, $65/pair SHIPPED.

Block adapter plate, fits automatic from 2003-2007, or G-56 from 2005-2015, $125 SHIPPED.

Also have other miscellaneous 5.9 and 6.7 parts available.

Reply, PM, Call or Text 402-780-5127.
 
Picked up a couple more longblocks.
I also still have the 2005 bare block with very clean bores, which should go back standard.

Mark.
 
Updated list:

Standard bore block, needs bored .020 over, $350, PLUS FREIGHT.

Standard crank, needs cut .010-.010, not scorched on any journals, $250 PLUS FREIGHT.

Cylinder heads, 5.9s or 6.7s, no cracks that I can see, $400 each PLUS FREIGHT.

CP3s, have several 5.9 ones, $175 each, SHIPPED.

5.9 Injector CORES, mostly 2004.5-2007, $40 each SHIPPED.

2006-2018 rocker boxes, $45 each SHIPPED.

2006-2007 AUTOMATIC transmission cooler lines, from the lower outlet to the rear trans cooler inlet, $100/set SHIPPED.

Oil cooler cover/filter head, $40 each SHIPPED.

Block adapter plate, fits automatic from 2003-2007, or G-56 from 2005-2015, $125 SHIPPED.

2003 engine from ahead of an automatic, has ~ 130,000 miles on it.
It's VERY, VERY RUSTY on the outside (PA snow plow truck), was running, but had a bad injector dumping fuel, no accessories such as alternator, starter, A/C compressor, ecm or harnesses, $1800 PLUS FREIGHT.

Also have other miscellaneous 5.9 and 6.7 parts available.

Reply, PM, Call or Text 402-780-5127.
 
Sky's the limit on what I have for 5.9 parts available.
Everything from pan to upper valve cover, fan to flywheel.
Injectors galore, as well as CP3s, rails and cylinder heads.

Mark.
 
Back
Top