12v hp #'s

I made 886hp 1770 ftlbs.

13mm pump
hx40 3b twins.
small shot of spray

made 810 on fuel.
 
wow man those are some great numbers! who else is out there with some good numbers? anyone?
 
Yea Love the pump! Not bad at all to drive on the street. A little jerky, but managable.
 
Previously
96 ram 3500 5spd
Stock 180hp pump
junk 370's
laser cuts
0 Plate
super b special 64/71/14
4gsk

532hp 983tq

Now running a 66/71/16ss
435's, 2095 plug, Yet to get back on the dyno for current #'s
 
0 HP. it's not running.

Thanks for asking though! :rockwoot:
 
Soon to find out hopefully!

887 pump re-man from DCP
191 DVs
(soon to be .078 holders stock now)
no plate
governor spring equiped afc, flipped washers, ground barrel etc.
(soon to try 2095 rack plug in 887 and dyno back to back)
5k CDS GSK
20* (going to verify with dial gauge tdc method soon, now set on timing pin)
afe stage 2 intake
4" down pipe to 4" stack
5 x .016" injectors with 280 pop pressure
T4 Header from Bodie
T4 T66 From Turbonetics (ball bearing cartridge, .84 divided housing, 68mm turbine)
Air Dog 150 supply system

Hope to crack 550rwhp but we'll see!
 
160 pump modded on the truck
80lpm ddp comp injectors
64.80-71 turbo
28.0 degrees of timing
11.54@117 dynoed 634hp
 
Last time I ran it: 215 pump, 181 DV's, stock lines, stock holders, plain ole' 370's and a Silver Bullet set me at 600hp, 650 with Water/Meth.

Jim
 
160 pump modded on the truck
80lpm ddp comp injectors
64.80-71 turbo
28.0 degrees of timing
11.54@117 dynoed 634hp

hey man I just saw your truck in diesel power the other day.


and great numbers evryone, keep them comin.
 
Im still waiting to get on a dyno, cant wait to see what i can put down with the mods in my signature hopefull 500+
 
i dont know ill hopfully be able to let u know in the spring when i get the brains and cash to get rid of my piece of $#!t centerfoce clutch altho it did hold for a total of 4 pulls *bdh*:badidea:
 
I'm hoping to get on the dyno at TS this year also but I don't know, my clutch isn't holding anymore either and now that I'm laid off don't see me getting a new one any time in the near future. First time out I hoping to see around 600 but I wont stop until I reach 700.
 
500cc pump from Scheid
5x.018s from New Era
Billet Goerend Trans
.093 lines
S465 w/.90 housing
AirDog 150
Light head porting
Helix2 cam

Never had a chance to dyno it but would hope to break the 600 mark.
 
913 pump never off truck
Full Cuts
Stock PDR 370's
4k springs
100 plate
HX35/wg14 over Stock HT60/26
16deg of timing

560hp 1100ftlbs
 
ddp4
022 d.v
215 pump with some work
stock head
stock cam
15.5*
water/meth

652hp 1181 ftlbs

Congrats Ponci on the magazine article truck looks good. I been following your numbers and posts all year good work.
 
Hey teddy bear how do you like that cam, I have one here waiting till spring to put it in. Any noticible gains? Spool up, egts? Thanks Brian
 
ddp4
022 d.v
215 pump with some work
stock head
stock cam
15.5*
water/meth

652hp 1181 ftlbs

Congrats Ponci on the magazine article truck looks good. I been following your numbers and posts all year good work.

What tires did you run the et in your signature with? What's your weight?
 
Back
Top