92 rclb Dodge ppumped

Zeppelin654

New member
Joined
Nov 11, 2011
Messages
843
Well guys, I'll be honest. I've had a few slight hicups with this truck and have come across a car I am interested, so I am not sure I need to have another truck at the moment, one that needs to boot.

It has 215,000 on the body, and 175,000 on the motor, but everything else has 1000 miles on it.

There is very minimal rust on it. Just two spots on the sides of the fenders. Rockers and underbody are perfect.

I replaced all of the brake system besides the booster:

calipers
rotors
pads
hand bent lines
master cylinder
all rubber lines
drums
springs for drums
shoes
e brake cables (all 3)
abs sensor
amsoil fluid
bearings
etc

new Suspension and steering parts:

new tie rod ends
alignment
steering stabilizer
red head steering box
borgeson high flow power steering fluid pump
vacuum pump seals
borgeson u joint style HD steering shaft
skyjacker soft ride 2.5" leaf springs in the front
bilstein 5100 shocks all around
heavy duty receiver hitch (recessed) with rigid industries led reverse light (hidden)
new vacuum hoses
amsoil power steering fluid

Engine and fuel parts:

all brand new 1/2" hoses
Hellman fuel sump
Fass 220 gph adjustable lift pump
donaldson water separator and fuel filter
dual feed to the 160 ppump
tork tek 060 hp overflow banjo (pressure never drops below 50 psi)
mack rack plug
power driven 7mm dv's
infinite performance 5x.016's 155* (weston's injectors and recommendation)
stock lines
no plate
AFC live
60 lb valve springs
4k gsk
billet tappet cover
billet stock lift pump block off plate
22* timing
PDR 5 layer intercooler boots
2nd gen intercooler and radiator
KDP tabbed
new front crank seal and new rear main seal
fumoto drain valve
Borg Warner SX-E 64.5/73/.91 T4
Steed Speed T4 manifold with stainless bolts
4" full exhaust
ss oil feed line and new oil drain
donaldson elf7349 oil filter and brad penn 15w-40 diesel oil has been used
amsoil coolant

Driveline/transmission parts:

mag hytec rear dana 70 pan
amsoil severe gear fluid
dana 60 front end with lockable hubs
all new u joints
sfi rated flex plate
DPC billet triple disc convertor

4x4 47RH trans with:

tcs billet input shaft
pcs billet parts (band, strut, acumulator and servo)
direct power pack from firepunk diesel (5 friction setup)
trans go full manual valve body constant pressure
2nd gear servo return spring from goerend
deep aluminum pan (temps never saw over 170)
48RE overdrive planetary set
5 pinion steel main planet upgrade

O/D and Lockup switches

NP205 transfer case

B&M pro ratchet stealth shifter
BD diesel remote trans cooler with fan (on switch) (in the bed of truck) 1/2" lines

Moto Metal 962 wheels 20x12 with 33" mickey thompson atz's (90% tread left)
Metal Lugz black spiked lug nuts
Extang tonneau cover

Isspro gauges:

fuel pressure
fuel level (new isspro sender too)
boost
pyro
trans temp
tach

New pioneer sound system with JL Audio 10" sub behind seat

Interior is excellent (minus headliner)

Truck Lite LED dot legal headlights

12141755_10153400759259064_3144835545059337745_n.jpg


944074_10153554413959064_9141909746068187556_n.jpg


12790883_10153638751404064_1633936111841907581_n.jpg


12801137_10153638751309064_1525227765494656216_n.jpg


10398372_10153708356789064_4882814117659344255_n.jpg


12548981_10153577414964064_3240406056631886565_n.jpg


12654258_10153581281534064_1089133955597727178_n.jpg


12524105_10153556322499064_4097488205692303892_n.jpg


12208442_10153435338884064_2558648192151204980_n.jpg


Now for the bad. I sent in an oil analysis report and here are the results. I see no coolant in the oil though. Dipstick looks perfect, as does oil fill cap. No oil in coolant. Truck runs awesome, so it beats me.

13557939_10153942329839064_7659085708331306125_n.jpg


ALSO. While in the middle of following Blackstone Labs recommendations, I suddenly had no forward gears while laying into the throttle. I am 99% sure the stock intermediate shaft broke (cleanly). I still have reverse, but no forward gears. The trans is currently out of the truck.

I have over $23,000 into parts on this thing and once back together, I am confident it will be a runner again. I have seemingly lost some of the original excitement and interest for this rig and it needs someone to get it back where it should be. I am being totally honest here and not trying to pull the wool over anyones eyes.

I am asking $18,000 OR BEST OFFER for EVERYTHING mentioned above and below

A stock 47RH will go with it, as well as a new 12v standard bore block, a 12v short block, 12v head thats almost new and has titanium keepers and retainers + 60 lb springs, new balanced crank, and extra ppump injection pump

13507240_10153942325404064_924024586887389870_n.jpg


13524334_10153942325454064_5873427141206555645_n.jpg


Please call me or text me with any questions at 814-460-3465. My name is Devin. Truck is located in Clearfield, PA 16830. Thank you
 
I forgot, but also included would be:

ECD billet front timing cover with gear driven lift pump
Mahle non I/C 286210 Pistons with swaintech crown and skirt coatings
England stock rods
Two sets of full cut dv's
Arp 425's
Full Gasket set
Two stock 12v cams
Cam gear
Pump gear
And some other odds and ends

Any offers considered. Thanks guys
 
Good luck with the sale, however I don't believe a broken intermediate has the symptoms you are mentioning.
 
I talked to a few shops including Firepunk and that was their guess. What do you guys think it could be. Planetary gears stripped? Forward clutches are out?
 
I know that usually intermediate shaft won't do that, but I personally broke one and drove it home in reverse.
 
I have broke 2 transmissions with same symptoms. It was the Belleville spring or however you spell it. It was to much line pressure causing it to push out and not return the piston in the forward drum. First one was the stock 48 spring was told to go to the 47 spring they could hold more pressure. Did the swap and it did it again.


Sent from my iPhone using Tapatalk
 
Last edited:
Back
Top