Pull-N-Power/NHRDA Indy Rules

Update

Update on a few things , after Pull n Power had a meeting

2 wheel drive trucks will be allowed as long as they meet all the rules for the class there signing up to pull in and will run a 26 inch hitch also

Trans Blankets. It has came to our attention that full block to tail blankets are not made for a few models of transmissions right now, In that case a Bell housing blanket will be acceptable, but expect in 2011 the full trans blanket in most of the classes regardless of RPM

This one mainly applies to work stock and 2.6. Hitches. Pull N Power does not want to see broken hitches make sure you have a good quality hitch with the correct opening for the sled hook. If using a drop receiver and clevis any drop over 2 inch is unacceptable. If they clevis looks like a poor quality it will be unacceptable. The final decision resides in Pull n Power tech officials. Pull n power will have loaner hitches at events to assure safety.

Thanks
Joe
 
Last edited:
Dodge and Ford Transmission blankets

All,

I have talked with All Season Diesel Performance and Bob Stroud and both are more than willing to work with us to design and stock full length tranny blankets for the Fords and Dodges. All they need are dimensions and a picture would be helpfull. Dimensions needed are the circumfrence of the bell and the rear of the transmission and the length from the block to the rear of the transmission. If you guys want to post that here or send me a pm, I'll be glad to act as the collection point to get this going. You can also email me at alanpage@indianatruckpullers.net

Thank you

Alan
 
Are full blankets the only option or is there a way to go say with a steel shield?
Just throwing that out there.

Lynn
 
Fireman450 said:
Are full blankets the only option or is there a way to go say with a steel shield?
Just throwing that out there.

Lynn
Click to expand...

No for P-N-P till full blankets come more available we our accepting a bell housing blanket, this only applies if your over 4500RPM for 2010

But also we will look into shields as were contacting Diest about making blankets.
 
house said:
No for P-N-P till full blankets come more available we our accepting a bell housing blanket, this only applies if your over 4500RPM for 2010

But also we will look into shields as were contacting Diest about making blankets.
Click to expand...

Thanks Joe. I have a bell housing blanket, If yall happen to get some rough quotes on what a full blanket would run (NV4500) Let me know.

Thanks
Lynn
 
Yeah while your at it possible what would roughly cost for a 47RE too. Lookin forward to the summer
 
Nice so we're gonna have to buy a bellhousing blanket for this year then then then turn right around and buy a full blanket for next year thats prob gonna cost more than the first one. I can fully understand the bellhousing blanket, there's a lot if mass spinning in there, but is a full blanket is really needed on a manual trans? Even the 2.8 or 3.0 class has only required a blanket or sfi can for the longest time.
 
Re blankets

HorsinAround said:
All,

I have talked with All Season Diesel Performance and Bob Stroud and both are more than willing to work with us to design and stock full length tranny blankets for the Fords and Dodges. All they need are dimensions and a picture would be helpfull. Dimensions needed are the circumfrence of the bell and the rear of the transmission and the length from the block to the rear of the transmission. If you guys want to post that here or send me a pm, I'll be glad to act as the collection point to get this going. You can also email me at alanpage@indianatruckpullers.net

Thank you

Alan
Click to expand...

You can also contact them directly with your specific application. I have also emailed Haisleys to see if they will get on board so please contact them also. Scheids is another one to call.
 
kxhonda said:
Nice so we're gonna have to buy a bellhousing blanket for this year then then then turn right around and buy a full blanket for next year thats prob gonna cost more than the first one. I can fully understand the bellhousing blanket, there's a lot if mass spinning in there, but is a full blanket is really needed on a manual trans? Even the 2.8 or 3.0 class has only required a blanket or sfi can for the longest time.
Click to expand...

If your over 4500 RPM this year, Next yer will be regardless of RPM
My Nv4500 one is a full blanket
I think most Manuals is full
The Autos are lacking behind right now
 
Alright that makes much more sense. Didn't know that the blanket for the nv4500 covered the whole thing.
 
kxhonda said:
Alright that makes much more sense. Didn't know that the blanket for the nv4500 covered the whole thing.
Click to expand...

It does not.

Stroud1.jpg
 
Mine looks just like the on in the picture. Who makes one that covers the whole trans.
 
the stroud on my dodge covers almost to the taill shaft IIRC
 
:rockwoot:Boy Is It A Great Day To Be Alive I HOPE EVERY ONE IS READY INDY IS COMING FAST. BY THE WAY DID I SAY ITS A GREAT DAY TO BE AIVE:Cheer:
 
ANGOLA DMAX said:
:rockwoot:Boy Is It A Great Day To Be Alive I HOPE EVERY ONE IS READY INDY IS COMING FAST. BY THE WAY DID I SAY ITS A GREAT DAY TO BE AIVE:Cheer:
Click to expand...

Yes it is a great day and today is also.:woohoo:
i can't wait to come up and play and show off:Cheer:
Dale
 
You must log in or register to reply here.
Back
Top