Pulling partout-Built Dana 80, 94-02 Flexalite, etc
- Thread starter 5shifter
- Start date
5shifter
New member
- Joined
- Apr 3, 2008
- Messages
- 264
Back up top
Dana 80-Haisley spool (one of the original styles--built heavier), 37 spline axles (only 3-4 runs), Brand New Yukon 4.88s, Girdled, 1550 yoke. Everything is setup ready to bolt under a truck.
$2400
Driveshafts--setup for an NV4500 and DHD 2nd gen reg cab long bed.
Front is for a 1410 yoke I believe. The rear is for a 1550 yoke.
$1000
Flamecut IH weights-around 550 lbs total--7 weights total slightly varying weights. Hangs on angle iron easily
$400
Stainless sheet roll pan with sled stops. One corner has a bend in it but can be straightened out easily. $100
I've also got an air/water cooler that fits in behind the bumper nicely. This was on a 3rd gen, but should work with a 2nd gen. Might have to make some adjustments on the cooler piping. Worked great with a 2.6 S475--$750 shipped OBO. This is not a Frozen Boost cooler
Dana 80-Haisley spool (one of the original styles--built heavier), 37 spline axles (only 3-4 runs), Brand New Yukon 4.88s, Girdled, 1550 yoke. Everything is setup ready to bolt under a truck.
$2400
Driveshafts--setup for an NV4500 and DHD 2nd gen reg cab long bed.
Front is for a 1410 yoke I believe. The rear is for a 1550 yoke.
$1000
Flamecut IH weights-around 550 lbs total--7 weights total slightly varying weights. Hangs on angle iron easily
$400
Stainless sheet roll pan with sled stops. One corner has a bend in it but can be straightened out easily. $100
I've also got an air/water cooler that fits in behind the bumper nicely. This was on a 3rd gen, but should work with a 2nd gen. Might have to make some adjustments on the cooler piping. Worked great with a 2.6 S475--$750 shipped OBO. This is not a Frozen Boost cooler
96cummins6.7
New member
- Joined
- Jul 8, 2014
- Messages
- 26
would u sell axles separate?
5shifter
New member
- Joined
- Apr 3, 2008
- Messages
- 264
Going to keep it together for the time being.
5shifter
New member
- Joined
- Apr 3, 2008
- Messages
- 264
Front driveshaft is sold.
Ready to get this thing gone and back under a truck.
Dana 80-Haisley spool (one of the original styles--built heavier), 37 spline axles (only 3-4 runs), Brand New Yukon 4.88s, Girdled, 1550 yoke. Everything is setup ready to bolt under a truck.
$2000 cash
Ready to get this thing gone and back under a truck.
Dana 80-Haisley spool (one of the original styles--built heavier), 37 spline axles (only 3-4 runs), Brand New Yukon 4.88s, Girdled, 1550 yoke. Everything is setup ready to bolt under a truck.
$2000 cash
5shifter
New member
- Joined
- Apr 3, 2008
- Messages
- 264
Back up top
Dana 80-Haisley spool (one of the original styles--built heavier), 37 spline axles (only 3-4 runs), Brand New Yukon 4.88s, Girdled, 1550 yoke. Everything is setup ready to bolt under a truck.
$2000
Rear Driveshaft--setup for an NV4500 and DHD 2nd gen reg cab long bed.
1480 slip yoke, 1550 pinion yoke.
$500
Flamecut IH weights-around 550 lbs total--7 weights total slightly varying weights. Hangs on angle iron easily
$400
Stainless sheet roll pan with sled stops. One corner has a bend in it but can be straightened out easily. $100
I've also got an air/water cooler that fits in behind the bumper nicely. This was on a 3rd gen, but should work with a 2nd gen. Might have to make some adjustments on the cooler piping. Worked great with a 2.6 S475--$500 shipped OBO. This is not a Frozen Boost cooler
Dana 80-Haisley spool (one of the original styles--built heavier), 37 spline axles (only 3-4 runs), Brand New Yukon 4.88s, Girdled, 1550 yoke. Everything is setup ready to bolt under a truck.
$2000
Rear Driveshaft--setup for an NV4500 and DHD 2nd gen reg cab long bed.
1480 slip yoke, 1550 pinion yoke.
$500
Flamecut IH weights-around 550 lbs total--7 weights total slightly varying weights. Hangs on angle iron easily
$400
Stainless sheet roll pan with sled stops. One corner has a bend in it but can be straightened out easily. $100
I've also got an air/water cooler that fits in behind the bumper nicely. This was on a 3rd gen, but should work with a 2nd gen. Might have to make some adjustments on the cooler piping. Worked great with a 2.6 S475--$500 shipped OBO. This is not a Frozen Boost cooler
5shifter
New member
- Joined
- Apr 3, 2008
- Messages
- 264
Dana 80-Haisley spool (one of the original styles--built heavier), 37 spline axles (only 3-4 runs), Brand New Yukon 4.88s, Girdled, 1550 yoke. Everything is setup ready to bolt under a truck. This rearend came from one of the top 2.6 trucks in the country a few years back before he went to a 3.0 chassis.
$1700, time to get this thing gone
Rear Driveshaft--setup for an NV4500 and DHD 2nd gen reg cab long bed.
1480 slip yoke, 1550 pinion yoke.
$500
Flamecut IH weights-around 550 lbs total--7 weights total slightly varying weights. Hangs on angle iron easily
$300
Stainless sheet roll pan with sled stops. One corner has a bend in it but can be straightened out easily. $100
I've also got an air/water cooler that fits in behind the bumper nicely. This was on a 3rd gen, but should work with a 2nd gen. Might have to make some adjustments on the cooler piping. Worked great with a 2.6 S475--$500 shipped OBO. This is not a Frozen Boost cooler
$1700, time to get this thing gone
Rear Driveshaft--setup for an NV4500 and DHD 2nd gen reg cab long bed.
1480 slip yoke, 1550 pinion yoke.
$500
Flamecut IH weights-around 550 lbs total--7 weights total slightly varying weights. Hangs on angle iron easily
$300
Stainless sheet roll pan with sled stops. One corner has a bend in it but can be straightened out easily. $100
I've also got an air/water cooler that fits in behind the bumper nicely. This was on a 3rd gen, but should work with a 2nd gen. Might have to make some adjustments on the cooler piping. Worked great with a 2.6 S475--$500 shipped OBO. This is not a Frozen Boost cooler
5shifter
New member
- Joined
- Apr 3, 2008
- Messages
- 264
Give me a couple days to get down to my parents and I'll get some pics up of the a/w
