Recent content by 04fummins

Does anyone know if I can use the GOS Ford 6.0 to CR Cummins Power Steering Bracket on a 12V cummins? I have a Medium Duty 12V Cummins and it has a LUK PS pump and it just does not play nice with the ford powerboost. I would like to use the original ford PS pump if I can. or does anyone know the...

Hello all. Long time since I have been here. I currently have a 2004 Fummins with 1997 Cummins 12v and a built 47rh transmission and replaced the input shaft on my ford nv273f t-case. the problem I have is that I guess I replaced the t-case input shaft with the wrong one (it should seal the back...

Hello all, Its been awhile. crazy busy with wind farms. I have been running around the last 2 years in my Fummins with my cobbled together transmission cooling lines, very leaky. So this past weekend I replaced all the lines with nice braided -6 AN lines and new cooler. well after I was...

I replaced the gear oil a few years ago and ever since the rear end has been leaking. Should I reseal it or should I replace it altogether? It looks like it is leaking from all the seals I know it is leaking out the end of the shaft on the pass side cause it is throwing oil on my exhaust and all...

Sorry for such a newb question but this is the first turbo I have ever had. I blew one of my boost boots off and noticed there was a bit of oil in there. What could be causing this? Could that be a bad seal? Am I in need of a rebuild? when I re-installed the boost tube, the truck ran well. I...

Started the conversion March of 2011 and just got her inspected last Friday. Took everyone in the shop to look it over but that was just to look at the "Cummins in the Ford". the inspection was, Honk the horn flash the lights turn on the wipers put on the sticker. It was kinda cool the crowd...

I have a LUK power steering pump 163 bar that has been shimmed to reduce the pressure. That thing is driving me nuts, it whines like crazy the steering feels fine but the brakes don't cut it for me no where near how it used to be. So I have decided to change it out with the dodge style pump. I...

Now that I have the 47rh in the truck I still need to get a temperature signal to the dash so the gauge will work. It is a crappy gauge anyway and I am going to add a real transmission temp gauge. Does anyone know if I can just fool it by adding a resistor like the dodge guys do. or should I...

OK, So I am just about done with my 6.0l delete in my 2004 SD. I have installed a 1997 12v with 167,000 miles out of a FL60 that had a 5 spd. The p-pump is a 190 hp and the timing is set at 11.5 deg. the motor is stock but it has a reman pump and turbo, it was an old FedEx truck. I have...

Does anyone know what wire feeds the reverse light on a 2004 F250? I have the 3 wire plug for the Neutral/Park/reverse lights on my 47rh and I hooked up pin 1 to 12v and hooked my test light to pin 3 and shift it into reverse and the light comes on. But I just can't figure out what wire in the...

Does anyone happen to know what the P.S. pump's pressure is in BAR? and also the flow rate might help as well.

Now that I sealed up my transmission/t-case I was test driving it and she runs good, takes off like a shot but right at about 10mph it falls on its face if I let off and ease back into it it will take off again then shifts into 2nd at 20mph and into 3rd at about 35mph. what do you think is...

Yesterday I got the modified drive shaft hooked up and filled the brand new tranny, but when I was test driving it, it developed a leak right at the T-case and Transmission. Should there be a gasket there? or is this a dry connection? I know the T-case fluid is sealed there and the tranny has a...

I am in need of a new Transmission I currently have a 47re in my Fummins but I want to change over to a 47rh. who should I get a tranny from? Georend doesn't have any 47rh's, so it is down to PATC or ATS I have heard some iffy things about ATS but I have not heard anything about PATC but I...

I have an 04 F250 with 12V and a 47re I installed a manual shift kit in the 47re. I have now hooked up the TV cable (had to get the whole throttle bracket) but none of the electricals are hooked up. It will drive but it doesn't stay in reverse and in drive 1 it takes at least 2000 rpm to get it...