Recent content by Cummins41

Anybody ever tried Nitro Gears or got any input on them?? We have tried about every brand in my 2.5 truck and looking for better options. This last set I got 5 passes out of... They were motives.

As the title says, I got a set of Yukon 35 spline axles and Yukon 35 spline spool for a Dana 80 cab and chassis or single rear wheel setup. Both have 1 season of pulling on them in a 2.5 truck. $800 for all of it. I also got a Mag Hytec Double Deep Tranny pan for a 47re/48re. Comes with all...

Well after 2 years building, we finally hooked to the sled for the first time friday night with Outlaws in there 2.6 class. For being the first hook on a completely new build and running against some of the best 2.6 trucks in the country, I was more than pleased with how it ran. Here is a link...

I'm not a vendor.... I should probably check before I post products

I have a custom VGT Switchblade Turbo from Blaylock turbochargers that I am wanting to sell since I made my truck a full time puller. This charger was great on the street with very very quick spool up. This is actually the only big turbine S366 that they built. Turbo has approximately 1,000...

I have a Maxed out 215 pump that I bought for my puller and ended up running across a good deal on a 13mm pump so I no longer need this. It has had idle only time since Seth at DPE tested it an flowed it. This pump was originally a Columbus Pump Maxed out at 600cc Fully adjustable from...

As the title stated, im wondering if I can make a Steed Speed for a 12v fit a 24v with the right milling. Does anyone know if this can be done? or if anyone has done it? I know many people to it with the ATS manifolds and those type but I didn't know if it was possible with these or not.

I got a set of tires an wheels that need to go to TS to be traded with a guy but we'll be busy in the field and I can't make it. It would be taking my set and bringing a set back. Willing to pay!

dick cepek fcII tires 3 are at 50% tread and 1 tire is brand New with less than 100 miles on it. these are $300 a piece. 305/70/16 in size The wheels are Ion Alloy 174 series, cost $650 New 16x10 8 lug dodge or GMC/Chevy style! $900, buyer picks them up or covers shipping

This is a Brand new good vibration 3 way dump fuel dump, 12 AN body with reducer fittings making it 10 AN. asking $130 shipped! These cost over 150 New!

Just posting this for a buddy 2001 3/4 ton dodge cummins -5 spd, new valair ceramic and Kevlar clutch -169,000 miles -superchips max micro tuner, 70hp edge jammer injectors -4" down pipe to 5" strait pipe with a 6" angle cut rolled edge tip -16" ion alloy wheels will need tires eventually...

I am posting this for a buddy, it is a quadzilla adrenaline with the v2 monitor. It was on a 01 dodge. Also has a bd stealth cover that comes with it! 550obo

This is a coolant bypass with everything to install except rear freeze plug. What is in the picture is what goes with it. I also have a 24 valve thermostat housing that could go with the deal they is already tapped for the 1/2in npt port but I would need one back in exchange. I decided to put an...

okay, I have searched and searched and havent found what im looking for.. so, I am building a pretty strong running 2.6 truck to run the SINGLE tire class with outlaws and this is a entire new build and im wanting input on axles... i know most of you will tell me 37's are the way to go and never...

Lookin for 2 aluminum 3rd gen wheels!