I've done the searches and done the reading but I'm still on the fence of somethings. I'm currently waiting to finally have my motor finished up. It's going to be .020 over, 188/220 cam stock bearings etc. The shop that is doing the assembling the motor for me wants to fire it up after they put...
As the title says, putting my truck back together the other night finally and when i torqued down on the first stud it didn't even get past 60 ft lbs and it stripped the threads right out of the block:bang:bang. I'm sure the issue has happened before I just haven't had any luck with the search...
Brand new tcs billet input shaft $550 shipped
Brand new tcs billet front drum $475 shipped
Brand new tcs billet combo kit (accumulator, servo, apply lever, strut and anchor) $200 shipped
Used jegs electric water pump $250 shipped
Will trade toward 12 valve parts mainly looking for a large...
I have a buddy that has a 02 3500 cclb drw 4x4 with intake exhaust and a efi autocal spade and our '99 6.5 dually at work is faster than it :nail:. Problem is when you run it WOT it takes off and then falls right on its face. Took a couple data logs and sent them to duramax tuner and they said...
Tcs products billet input shaft brand new $600 shipped
Tcs products billet front drum brand new $550 shipped
Hamilton 200/220 cam with gear and bolt on retainer used $550 shipped or trade for 188/220
delivery valves I was told they were 191 when I bought them, they have 052 and 179 on the...
I've been looking around for the last few nights and can't find the info I'm looking for. I'm getting ready to put twins on my '95 and am planning on removing the heat exchanger and putting a trans cooler with a fan in place. How ever my question (even though its probably a stupid one) is do I...
I've read the rules at the M.A.P.A. website and am having a problem putting it all together. What all do I have to do to pull my DD if I was to put twins on it?
Thanks Twigg.
We're getting ready to put a set of injectors in a '93 CH613 Mack with a E7 350 at work tomorrow. I've been searching all evening trying to figure out exactly what needs to be done to complete the job and what all specs I need for when putting it back together with no luck. Is there anyone on...
Ok guys just changed the fuel filters in the bosses new to him truck at work, ran fine the whole day. Took it out that night parked it and came back out a little while later and it would only run for 2-3 seconds at a time and check charging system light came on. After a few minutes it finally...
Where is the best place to get a water pump from other than the stealer ship for my 06? Its created a little leak and with my luck its only going to get bigger. Are the ones from genos garage any good for the $35 they are?
I've tried searchig but didn't have any luck. Ok so the trans in my 95 (truck in sig) has created and issue where going down the road it will lock and unlock and kick out of O/D, I mainly notice it happening when I hit a bump it seems but even while just cruising down the road doesn't matter if...
In a couple weeks I'm going to be towing a 10ft by 18ft shed back from the South Boston, Virginia area to Denton, Md and as the title says I'm woundering what permits I'm going to need and how I have to go about getting them. Any help is greatly appreciated.
Thanks Twigg
Alright guys the other night on the way home I a burn out with the truck in my sig and now the limited slip is acting up. It acts like it has a locker in it and is full time posi going down the road and making turns. Does anyone know what it could be, did i fry the clutches in the limited slip...
I'm posting this up for a buddy of mine who needs a few parts to get his 04.5 Dodge 3500 dually fixed. Feel free to call him anytime 443-786-1918 his name is Will or email me at dontwi4944@yahoo.com
The list is:
Colors do not matter
4 door cab
Passenger side doors
8' dually bed
Driver side...