Search results

Saw this over on 1stGen.org...thought there might be some interest here. ;) 1stGen.org ? View topic - Dash Guage Pods !!! So This was a timely post for me, since I was about to bite the bullet and purchase a 2nd Gen 3 pod dash unit to use....but would prefer the 1st gen Banks unit. I have...

I'm looking for a 4wd auto tranny from a 91/92/93 cummins truck, prefer with converter, looking for a decent driver quality, or good rebuildable core. I'm in the Vancouver BC area, but will travel 4-5 hours one way, so most of southern BC, and WA state, or even Vancouver Island. Might even...

Last few weeks I've noticed that my shifting between gears is starting to get a little sketchy. Especially 1st(low) to 2nd...it's like the tranny is not slowing down enough and your grinding them into 2nd....not super fast, but enough to make it a chore. 2nd to 3rd seems good, but 3rd to 4th...

90-93 Electronic gauges, Volt, Temp, Fuel, Oil pressure. All confirmed working. $15ea or $50 for the set. 81-89 gauges, Amp, fuel, oil pressure etc. $5 each Non-IC upper and lower rad hoses, used...$20 for the pair Non IC air box to turbo tube...$25 1995 2wd NV4500 tail housing, with hole...

Never mind...I will link to a site that will let me post pics easier. ;)

My left turn signal bulb in the dash popped on, and stayed on, while I was out getting groceries. It does this if a running light is out. Checked the truck and my lower front fender side amber light was out. Got home and popped in a new bulb...nothing. Hmmm try another bulb...nothing. Go...

I wanted to put out a solution I have found that seems to work on my truck. Just did this today actually. Every so often my WTS light, as well as the water in fuel light, stop working. It has done this at least 3 times over the past year, since finishing the 4wd conversion on the crewcab and...

Well today I decided to see where my "Bang/Clunk" was coming from in the front end. I was pretty sure it was the steering box, but had my neighbour crank the wheels back and forth while I watched and listened. Sure enough the box torqued in one direction, then when direction and torque was...

This is an old thread over on Diesel Bombers...but I could not find reference to it in our archives. Very interesting information, and confirms my aversion to the K&N type air filters. ;) http://www.dieselbombers.com/chevrolet-gmc-diesel-tech-articles/16611-duramax-air-filter-testing.html

Not sure why I have such a hard time posting photos on this board...so here is a link to this thread, on a more picture friendly board. ;) http://igotacummins.com/showthread.php/3775-Smoothing-out-Smooth-Ride-Springs-1st-Gen?p=38286#post38286

Well I decided I would getting the front end to ride a bit smoother with the help of the thread below and user sevnt300 and his findings. Those "smooth ride" parabolic springs I installed during the 4wd conversion really did not smooth anything out in the ride....actually I think it made it...

Wouldn't post pics....so go to this link instead... http://www.dieseltruckresource.com/dev/showthread.php?p=3255824#post3255824

A little trick I have been using while working on interior stuff. You probably all know how hard it is to find the darn screw holes under the carpet and insulation, once you have removed a piece of trim, shift boot or other piece. Well I figured out a way to make it relatively easy to get your...

So my question is this....Will the magnets on the harmonic balancer for a tach effect the CPS sensor? I was running the two magnets...180* apart on my fluidamper balancer for a tach. This was on my 89 motor so I did not have a CPS sensor. But since I'm switching to the 93 motor from the 4wd...

I've been working on getting the NV4500 rebuilt, and converted to 4wd. I just finished assembling the back side of the new fully splined 4wd mainshaft and went to install the rear bearing expecting it to be "tight" and the bearing fell into place!! I measured my old 2wd mainshaft where the...

Well today was the day. I finally decided to swap in my NOS 9mm Bosch injectors into my motor. The truck has been progressively smoking more and more since I started driving it 18 months ago. And with the help of the DTR I was hoping it was leaking injectors. I have never done an injector...

I am usually over on the DTR, but I jump over here from time to time and lurk around. Figured I better make my presence official. I have a 84 Dodge D350 Crewcab SRW with a 89 CTD and a 96 NV4500 and a 3.54 Dana 60....this is my daily driver!! Have had it about 18 months and can't believe I...

Looking for a shifter from a "bottle top" (94-98) Cummins NV4500. Would like the complete unit from lower stub to shift ball. But would consider just the lower stub and related hardware as well. Let me know what you have. PM me here.

Looking for the two lower water/coolant tubes used to run to the tranny cooler used on auto equipped trucks. Please PM me if you have them. Thanks.