Search results

ADII tower/pump only ...... was a replacement but I sold the truck. BNIB. I kept as a spare in case I ever had an issue not to be stranded. $75 plus shipping. PPUMP delivery valves and holders ... this was for a 600-700HP ppump - they were from weston I believe from memory No idea on size...

Letting fate decide on my truck. Yes its for sale.
Original Add when I purchased. ============ Selling my 2000 Dodge Ram. This truck was built as a street warrior / pulling truck. On twins the truck makes 1068hp / 1886lb/ft. On a Single s400 it makes 786hp/1189 ft/lbs. The truck started out...

Guys If I pull the head to upgrade head have a couple of questions given that the block and the head are both supposedly orringed (Previous Owner). 1) Can i re-feed the wire and seat myself without to much drama ? Mainly the bock as the new head will be orringed as well and will have shop do...

Pm me :p Sent from my SM-N900V using Tapatalk

Low miles. Ran great. I have 3 different sets so 1 has to go ..... pulling as we speak. $ 475 Sent from my SM-N900V using Tapatalk

Did one a long time back .... be in driveway again. Looking for any tips on rear main as well as best trans jack. Was thinking of using http://m.harborfreight.com/1500-lb-capacity-atvmotorcycle-lift-61632.html But not sure if any jack will balance trans as well as transfer case together...

Guys Need a rear wiring harness for a 2000 long bed truck ....auto 4x4. From drivers fender back. Thx Sent from my SM-N900V using Tapatalk

So - here's the story. Bought the truck with ABS light on. After replacing the rear sensor figured it was the front sensor as the hubs looked a little rough with rust etc. Replaced those quite a few months later and no change. Since I live in FL wasn't too concerned with ABS so kept on...

Trade for Tools .... impact etc Partial towards injectors for ppump 24v AFC live Other stuff...... ;) Sent from my SM-N900V using Tapatalk

What year and engine trucks are compatible with 2000 3500 CTD. All 3500/2500 98-2002 gas and diesel ? How about 1500's ?? Bolt pattern and length etc .... thx Sent from my SM-N900V using Tapatalk

Guys My ABS module is toast. Having a hard time finding replacement part or a good rebuilder. Any ideas ? Where can I find the exact part number for the ABS/EBCM module based on VIN as the sticker on mine is rubbed mostly off. thx

For a 2000 truck

70 miles from home and airdog just died. Truck still seems to want to run ..... Is it safe to drive slowly home ? Ppump conversion ,

Think mine has a dead spot. Lmk. Thx

Only selling as stepped up to a full 2.5 carli kit. Around 6 weeks use. Good for the money ... deals with rear issues which is where these trucks hurt. Easy install. 280 plus shipping ..... 380 new so $100 off for 6 weeks Sulastic Photo by fakdaddy | Photobucket

Hey guys Need a voltage reference for someone running a ppump conversion with a TPS. I'm having problems with lockup under mild throttle and think this might be the issue. Basically it requires 10% throttle instead of 2% throttle (picking guess numbers) to lockup at 45+mph (OD on) for example...

Mines missing ......need a new one Thx

2nd gen compressor outlet t3 Billet wheel $1800 new .... has less than 10k miles Will post turbine specs when I get home on sunday but believe it's a 66/74/0.9 ...66/74/14 Flowed real quick and probably best single charger I've run out of around 8 over years. 20140117_180528.jpg Photo by...

Brand new thinking about stepping up to long arms. Save you self a 5 week wait and a few $$ 420 shipped OBO 2.5-4" 2nd gen only

Need the following. Dust cover for flywheel barring port on passenger side Brackets for proportioning valve/brake lines on frame knuckles for front steering/joints PM me :)