Search results

I have a stock turbo off of a 6.7 with 106,000 miles. Worked perfect when removed, no excessive shaft play, vanes operate properly. Just went to an s400. $350 Next I have a 4" to 5" down pipe for the stock turbo. It also has the cast elbow on it. I can remove it if you don't need it. The pipe...

Nv4500 4wd set up for a sled puller. It has a Kenny's 1 3/8" input shaft. Has 5th gear removed and a girdle plate installed. 4 bolt shifter top. Never pulled. Unknown mileage but looked great when disassembled. $1,500 with bell housing. picked up. Will ship on your dime Cummins adapter...

I am looking to sell my 1998 VW Jetta TDI 5 speed. I bought it last summer as a non runner. Got it running and found a few more issues. The biggest being the #1 lifter having a deep wear mark, resulting in a crack in the lifter. The cam looks fine for the miles on it, which i was told was in the...

Bought from a member on here. It's got a 12" opening and necks down to 6". Then it turns to 5" at the shut off. This is not a cheap blast gate. As it is you can cut the grill out and it sets on the bumper of a 2nd gen. Comes with a leather cover for hauling. $375 plus shipping.

Used. $300 plus shipping

Like it says. Input is used but straight. Hydros have idle time only. Input : $300 shipped Hydros : $300 shipped $550 shipped for both

This is the type 22. It has 1 1/2" bungs welded in as opposed to the factory 3/4" bungs. It also has 4" vbands welded on the charge air outlets. Very little run time on the IC. New they go for $500 plus shipping. I will take $500 shipped.

I bought this used from a member on here. 5 hooks on the clutch. No hooks since I have owned it. I also have brand new SB hydros $2350 for clutch and input shaft. $2650 with SB Hydros. Buyer pays shipping.

'96 5.9L 12v IH stamped 14mm main 2.6 engine. Rotating assembly blue printed and balanced. All machine work and assembly done by Drew Pumphrey (D&J Precision Machine) Std bore Interstate McBee rod and main bearings. Ross forged pistons. Bowls and reliefs by D&J. Total seal rings Cummins...

01 qcsb 2.6 truck White. Paint looks good on the upper half. Has the typical dodge door and lower cab rust starting. Can be easily fixed still. Has fender flares. Cowl is cut out and firewall is still Intact. Interior is stripped except for headliner and door pads. Dash appears stock with...

Velocity stack Throttle bracket

Mahle 286210 12V pistons .250 reliefs $350 12 throttle bracket and rod $150 Pump support bracket block side only $45 P7100 Pump gear $75 Vibrant velocity stack 5" $65 Dsr lift pump $400 -8 3 way dump $ 100 24v Valve cover. $100 24v engine mounts $100 Buyer pays shipping.

Wondering if anybody has done this. I know haisley does it to make room for a velocity stack. Wanting to do the same thing, but just curious if any one has some good pic to go off of. Application is a 12v in a 2nd gen dodge.

I have a Borg 475 with an NADM/FPP legal 2.6 stepped cover compressor housing. It has a 96/88 turbine with a 1.32 housing. Cast comp wheel. $600 shipped

I have a Borg 475 with an NADM/FPP legal 2.6 stepped cover compressor housing. It has a 96/88 turbine with a 1.32 housing. Cast comp wheel. $600 shipped Master craft courser C/T's with about 50% tread. 285/70/16. 4 of them. $500 local pick up of buyer pays shipping. 4 stock dodge dually...

I have four (4) of these. They are 50% give or take. $600 buyer will pay shipping. I will take them and get a quote before we finalize the sale. I am located in the 44406 zip. I usually go to Michigan once a week, so I could possibly meet/ deliver if we're close also.

Have a friend with a 12v auto. Complains that it lopes in gear and when it gets up to operating temp it will stall. It has gotten worse in the last week. Also when in D, if you try to power brake it, the throttle gets very stiff and it won't rev up. I replaced the overflow valve with a Tork...