F250/Cummins Swap

Ordered an entire bag of those zip ties to pretty much use two of them.

I went and got a set of washers. I don't like the thought of the poly bushing on the DCS mounts pressuring down into the slots in the mount.

Ye old AN fittings for the trans lines.
185b486bfb4be138cf07bd50f39d1273.jpg
42eb983b0bc3522d67a8689b75cd1f6f.jpg
921581bd58a69705b50d0a70c3f0d93c.jpg
119646ad11a9ea665111b15a329941a0.jpg
e02770aedbf96c32b5234792a7949cf8.jpg
ec475ee8b6efe3fb3f8d2dc92a8b3b51.jpg
47132d8843c4e9afd6fcf7670a97bc0a.jpg
3d2ab4ae7d2b10a97c30f5690c0f6926.jpg
1144f0d7d14c9c2f8b9f875da2b3f51a.jpg


Sent from my XT1575 using Tapatalk
 
Eh. It was supposed to have sparkles in the paint, but that was a giant failboat.

It didn't occur to me that ATS was that color. Oh well.

Sent from my XT1575 using Tapatalk
 
Bwahahaha someone beat me.... Fack
ea7a7093e60712a80dd1a8657df7cfef.jpg


Sent from my XT1575 using Tapatalk
 
looking through your build thread i see you work at our local whayne dealer, I am currently building an 06 f350 with 5.9 cr. have you used the anteater stc before as i see that's what your going to be using? I have been reading up on it but not dead set on it yet
 
I'm a beta tester for the Anteater. I put about 40k miles on this one in my dodge, and it will be installed in the Ford and run again.

PM sent your way.

Sent from my XT1575 using Tapatalk
 
Went kind of ape **** tonight. Drove the truck in at 5. Had the Cummins in the frame at nine pm. Cross member will need to be modified for the wider Chrysler trans mount. Got rust under the cab to clean up. Power steering hose from the gas PS setup also fits the trw Powerstroke pump so that was a score.

Jackasses at rhino liner (previous owners doing) put bed spray on the bed mount bolts. They will have to be torched out.

Should have the airdog installed tomorrow and have some indication of what I'm going to do to the fuel pump module. I wanted to do a B&W turnover ball but it's not in the cards for this weekend.

The GDP intake horn has a high probability of being a cluster **** because of its proximity to the abs pump. I this a 30-45 degree silicon boot might correct it though.
6b7cbd52cdff3956126adacdffd5f342.jpg
0fab2c1464ff8b20135e213acbe5090c.jpg
0aac83c69011c66a505d9e03e7ade678.jpg
0fe84dfb02daa6f03005d545862c5950.jpg
9ed6389e122cd9a9ee36bd6eeb8055f4.jpg
9672018e0e43ca439fc21d4e8fdb82f4.jpg
f447e9304dc65abe798a975556e8094c.jpg
48f742dfb1f18f7e8d06da74cc73bba0.jpg
62bff0af5341b43d7b5d82684de0332c.jpg
d98f7991814645b4686d726ff15f6158.jpg
76574894cb42e35fda4271ac0b068f56.jpg


Sent from my XT1575 using Tapatalk
 
Oh yeah, I fabricated spreaders to fit our wheel lifts to lift the cab. Had 4" flat stock broken into U's and then when we found the balance point of the cab, I pulled it all off and burned it in.

Sent from my XT1575 using Tapatalk
 
I didn't take pictures, but I got under the cab today and stripped the rust and then primered it.

I also murdered my crossmember (only a little). I initially thought that I could just widen the distance on the same center as the Ford trans mount. In reality, the Ford mount is offset, and was throwing the trans and engine out of place.

I eye-balled it, and the driver side ford slot needed to stay, and an additional slot added on the passenger side. This puts the tail of the trans where it needs to be for the Tcase to clear the frame, and also puts the center of the fan hub at 19.5" from the outside of each frame rail.

I also noticed that the DCS engine mounts are out of plane from one another. You can see the difference in rake from front to rear.
0ab469ae0ee5b241b4385eb10450ce63.jpg
1254093ae6df168cbec338e9e37a5aa9.jpg
ef0a7bb22acf78346395a22ab5f889f7.jpg
5e4f73dade41c0c2a4ea3608bde4b58d.jpg


Sent from my XT1575 using Tapatalk
 
My 'Help' (slave drivers) insisted that we were stripping rust and painting the frame. The last thing we did last night was pressure wash thoroughly.
Hit it again at 7am this morning. I hit about 10 more rusty spots under the cab this morning and primered them.
Then we undercoated all of the cab floor.

We welded up the trans crossmember to leave only the two needed slots and then painted it.

I picked a place for the airdog and schemed on how to use the OEM lines and pickup.

We sat the engine for the last time and connected the power steering hose at around noon.

We removed the last of the gasser exhaust from the hanger isolators and tried to install the JAMO exhaust. They welded the mounts on the over axle hump incorrectly so that will need to be fixed to go on with the exhaust. The downpipe needs to change to move away from the frame so I'll have that done at the same time.

You can also see the mag-hytec pan is on in that picture.

I flipped the power steering pressure line to bow to the rear. After we set the cab, I think I'm going to pull it back to the front.

Parts stores don't want to sell the nylon seal that goes on the pressure line.

Between the engine weight change and new poly cab mounts, the fenders sit over an inch higher above the tires.

I'm going to be using a 6.0 Ford engine fan with dodge electronic hub. We cut the 5.4 fan shroud to a diameter of about 24.25". The 6 liter fan is roughly 23.25.

I'm going to fit all of it before I try to go larger on the opening.
72eca487198ab57c0ae9ae13a07e1a9a.jpg
a78eb81f6df362967290e84023228be8.jpg
29d7abe7d1adedba7fd84856fb865218.jpg
00b4e261a22011deb5303c259fbd5eb8.jpg
87906a177ee557560d8e550694317b03.jpg
87de3e1a226a4aef34efe2cadd195ad3.jpg
0db6c230c49b8f81fe30ba2d8f820ab3.jpg
22a95047dbd15723734c188882d30d33.jpg
3c1cebdde00a874b30eea0de1d0d9af8.jpg


Sent from my XT1575 using Tapatalk
 
Looking good. You’ll be glad you took the time to paint the frame. What did you use for undercoating?
 
We had a surplus of duplicolor undercoat from a school bus warranty repair. We dumped about 4 cans. I still have to do the bed. I set fire to the bed liner. Turns out rhinoliner reacts to oxygen and heat the same way grease does.

Sent from my XT1575 using Tapatalk
 
I think I still am anyway

Sent from my XT1575 using Tapatalk
You have beta code still flashed, I think? I can't imagine doing one of these swaps without some form of electronic transmission control.
 
Was out reflecting on what needs to be done this week and spotted this.

I vaguely remember something I read stating there was an issue. Maybe the thread on pirate. I will have to decide whether to use a button head screw or omit it completely. I'm not entirely certain that the frame side mounts don't need to be repositioned just a tad.
362e2051fd1ef63039425ac4f1a45e6e.jpg


Sent from my XT1575 using Tapatalk
 
Where can I get performance intercooler mount bushings?

Sent from my XT1575 using Tapatalk
 
Back
Top