My Dream Shop 48x100

[not enoughsmoke]

Looks good , how much do you plan on lifting again with that ?

Sent from my SM-G955U using Tapatalk

500lbs at the most. Mainly cylinder heads or crankshafts when building engines ETC.

Looks good. I had some back to back strut that I gave away to a family member. Never thought to use it for a small bridge style crane. Where do you buy the end trucks? Can you snap a closer picture of the ends where the bridge attached to the rails?

it will be a month before I can snap a pic but I can
https://www.amazon.com/dp/B09JFDH39G?ref=ppx_yo2_dt_b_product_details&th=1

 

[not enoughsmoke]

Got tired of trying to work around the milling machine. So I moved it. Then I continued to run electrical and lighting

 

[4x4dually]

Very nice.

 

[Smokinrebel]

Lasers and the right color thhn for 120v circuit...what in the world

 

[4x4dually]

Lasers and the right color thhn for 120v circuit...what in the world

Conduit bends look nice from what I can see. Strapping it up with a laser takes this to a whole new level of OCD. Even I'm not that bad. LOL

 

[not enoughsmoke]

Lasers and the right color thhn for 120v circuit...what in the world

i know :hehe:

Conduit bends look nice from what I can see. Strapping it up with a laser takes this to a whole new level of OCD. Even I'm not that bad. LOL

Its it OCD or CDO love that laser for this work and angle finder

 

[Smokinrebel]

Conduit bends look nice from what I can see. Strapping it up with a laser takes this to a whole new level of OCD. Even I'm not that bad. LOL

I was going to be one to say it. But I sure can appreciate it!

 

[not enoughsmoke]

I was going to be one to say it. But I sure can appreciate it!

well if someone else does it you wont notice it as much as when you do it. Cause every time you walk by it or look at it you will notice and appreciate it.

 

[Smokinrebel]

Couldn't agree anymore. Good work

 

[not enoughsmoke]

I got the power ran, finished putting up the lights, and continued to put up the ceiling metal

 

[not enoughsmoke]

I Ran the Electrical for the air Compressors and got 1 hose reel mounted with my 2 helpers

 

[4x4dually]

Why two small motor compressors? Just going for redundancy in case one goes down, or to keep them cooler?

Dad has a setup in his shop now where they are all three valved together. Normally, there is an 80 gal vertical for the north shop wall and the other 80 gal vertical is plumbed to the south wall. The 120 horizontal 3-stage, 15hp can be valved to either wall or they can all be tied together for one big ass capacity. Are you splitting them up like that or is one for the tool room and one for the open shop area?

 

[not enoughsmoke]

Why two small motor compressors? Just going for redundancy in case one goes down, or to keep them cooler?

Dad has a setup in his shop now where they are all three valved together. Normally, there is an 80 gal vertical for the north shop wall and the other 80 gal vertical is plumbed to the south wall. The 120 horizontal 3-stage, 15hp can be valved to either wall or they can all be tied together for one big ass capacity. Are you splitting them up like that or is one for the tool room and one for the open shop area?

Well the 80 Gallon tanks compressors have CFM of like 15.8 CFM and the old one I have is 18.1CFM. The neighbor was selling and downsizing and had the same compressor that i had with practically no use on it. So I bought it as well and just to have redundancy as well. My plan is to run the air on the a header loop in the top of the shop and use the offline compressor as a storage tank. When not in use.

 

[4x4dually]

My plan is to run the air on the a header loop in the top of the shop and use the offline compressor as a storage tank. When not in use.

Good idear!

 

[not enoughsmoke]

Here is another view of the shop space since I got the Red truck out and move some of the lumber as well as more air lines

 

[not enoughsmoke]

More air lines and reels installed. Also got time to finally put in a sewer vent i didn't want to cut a hole in my roof and risk a leak

 

[not enoughsmoke]

started mounting flood lights on the awning

 

[not enoughsmoke]

finally got a chance to test them at Dark, but probably gonna add more.

 

[bateman]

Man I’m jealous. You’ve went above and beyond haha looks good

 

[not enoughsmoke]

Man I’m jealous. You’ve went above and beyond haha looks good

Thanks man I appreciate its still a lot of work ahead of me.