5.9 CR and 6.7 parts, blocks, cranks, heads & more

dangerous06 said:
is an industrial cummins 6.7. Manufactured in 2011 the same base engine as a dodge ram? Just the block and head?
Click to expand...
If it has the narrower spray pattern (123*?) injectors and piston bowls, they would also be nice to have.

Guys, at this point I am stuck here.
Rain keeps making the place a muddy mess and if I WERE to actually make it anywhere to deliver parts, it'd be over back east/southeast.
Those poor guys have been waiting a while. :(

Mark.
 
I'm hearing what you are saying, but if I can go to CA, I should be able do MD first.

Mark.
 
Mark, I called you Thursday and i never heard back.Do you have the 06 Manual ECM??????
 
No, thought I might, but it's an auto that I am hanging onto for a stand alone to test fire with.

Mark.
 
Just picked up a notable amount of 5.9 CR stuff.

One is a very, very nice early 2003 short block, with machined cap rods, that literally is THE nicest used 5.9 CR I have had in a long time.
It will not need bored, but a re-ring is always recommended.

I also have quite a few CR heads, both 6.7 and 5.9s.

Mark.
 
I also have a 6.7 short block with a standard crank and a notch in the deck from a bad head gasket.
The notch is between cylinders 3 & 4.
See attached pic.

Mark.
 

Attachments

  • 0309151013.jpg
    0309151013.jpg
    66.6 KB · Views: 0
Been picking up an inordinate amount of 5.9 CR stuff lately, some blown up and some REALLY nice stuff, lot of 2006 and 2007 pieces.

I have so much of this stuff, I could just about start building my own long blocks and selling remans! LOL

Mark.
 
Mark Nixon said:
Been picking up an inordinate amount of 5.9 CR stuff lately, some blown up and some REALLY nice stuff, lot of 2006 and 2007 pieces.

I have so much of this stuff, I could just about start building my own long blocks and selling remans! LOL

Mark.
Click to expand...

Quit bragging and send me my parts! LOL AND a 6.7 block no charge!
 
Did you still want the USA rockers, or am I just sending rods?
I have the perfect "free" 6.7 block.
It has half of 1 side blown out, but you still need to pay shipping. LOL

Just teasing!
It's in my pile of cast and going out probably this next week.

Mark.
 
Last edited:
LOL Yeah send me a set of rockers since you have soooo many! LOL Any12v rod caps in that pile I need 4!
 
You're wasting your time with finding caps for those 4 rods, plus re-sizing them is a long shot. Just scrap them and move on. :D
PP me the money on the rockers and this stuff will leave on the Pony Express to-morrow or next day.

Mark.
 
I'd make someone a hell of a deal on cylinder heads right about now.
I have probably an even split of a total of 16 CR 5.9 and 6.7 heads, some ruff as a cob, others basically bolt on and go.

No, I won't sell them for $150 apiece and deliver!

Also have a few (3-5) VP boat anchor heads, too. :(

Mark.
 
I still have more than enough to piece together some very nice standard bore long blocks in a 5.9 OR 6.7.

Or I can mix 'N match cranks with blocks and make stroker derivatives. :D

Mark.
 
Quit teasing and drive a 6.7 block out to me! You know you want to put your toes in the sand! LOL
 
Believe me, if I had a machine shop at my disposal, this stuff wouldn't be sitting here, I'd have it done up and out the door.
 
You must log in or register to reply here.
Back
Top