Truckers, lets see your rigs!

[jfaulkner]

I found Faulkners new truck!

Sent from my SM-G930W8 using Tapatalk

Thanks azzhole, ruined the unveiling party. The floors wet because the ladies saw it.

 

[Rig Wrench]

Thanks azzhole, ruined the unveiling party. The floors wet because the ladies saw it.

Doubt the guy drivin that is into ladies...

 

[dummins]

But think of the mpg’s That pile of whale cum would get, them wheel stimulators. ����

 

[jfaulkner]

But think of the mpg’s That pile of whale cum would get, them wheel stimulators. ����

Probably has to wash it weekly since it runs the fuel tanks over with all those fuel saving devices.

I bet he pulls a log wagon with it in Maine.

 

[Rig Wrench]

Hauls sailboat fuel. Gets great bsfcs

 

[lorendiesel5.9]

Actually it looks like he's almost a full mpg back. I bet he would be in the 4s doing what I do running the same routes.

I run SE Wisconsin, southern Minnesota, Iowa, Missouri, Nebraska, and Kansas. What part of that is good fuel mileage territory?

 

[jfaulkner]

I run SE Wisconsin, southern Minnesota, Iowa, Missouri, Nebraska, and Kansas. What part of that is good fuel mileage territory?

Ever notice how all the super fuel mileage trucks always weigh 65,000 and run in areas you can watch your dog run away for 3 days?

I want to see one pulling a D9 across 68 in PA or in WV with 50ton in a coal bucket on a tight schedule.

 

[Leiffi]

4900 km behind, 100 km to go. Altai mountains, eastern part of Kazakhstan.

 

[hotfarm1066]

Except for Faulkner

 

[Rig Wrench]

4900 km behind, 100 km to go. Altai mountains, eastern part of Kazakhstan.

Truckin with Borat

 

[jfaulkner]

Except for Faulkner

Can’t wait until my cabover Volvo shows up.

RigWrench is sourcing me a European super turbo and special tune to run it.


Until then I’ll just clean this turd.

FYI a 6,000rpm grinder will chuck a polishing brick Mach 2 into your shin and it will hurt.

 

[Rig Wrench]

You need a meth head jonesin for a fix. It would save your shins

 

[dummins]

Buy more wheel stimulators and you don’t ever have to worry about polishing, think of the bsfc’s!!

 

[BRE]

Got to roll all day Friday like this... until I made it east of the Mississippi. Rain ruined it.

First full tank didn’t net a bit of difference in mileage. I knew I got my hopes up. Guess we’ll just keep inching along.


Sent from my iPhone using Tapatalk Pro

 

[allan5oh]

I run SE Wisconsin, southern Minnesota, Iowa, Missouri, Nebraska, and Kansas. What part of that is good fuel mileage territory?

All of it compared to where I run. Finally saw above freezing for half a day yesterday!

 

[jfaulkner]

You need a meth head jonesin for a fix. It would save your shins

I’ve had the homeless truckstop crack heads polish wheels before and not much luck. Had them done in Georgia a few months ago and still chit.

I can get round hole Alcoa’s for $200 each so I’m thinking long and hard about it before I do all 4 trailer axles

Buy more wheel stimulators and you don’t ever have to worry about polishing, think of the bsfc’s!!

I still need to find someone to pawn those goofy covers off on.

All of it compared to where I run. Finally saw above freezing for half a day yesterday!

You need Leiffi’s bad arse ride. A Volvo doesn’t know what a hill is and can get 10mpg by accident at 1100hp.

 

[jfaulkner]

Got to roll all day Friday like this... until I made it east of the Mississippi. Rain ruined it.

First full tank didn’t net a bit of difference in mileage. I knew I got my hopes up. Guess we’ll just keep inching along.


Sent from my iPhone using Tapatalk Pro

You need to give me 10min with that to try something.

 

[Leiffi]

Can’t wait until my cabover Volvo shows up.

RigWrench is sourcing me a European super turbo and special tune to run it.


Until then I’ll just clean this turd.

FYI a 6,000rpm grinder will chuck a polishing brick Mach 2 into your shin and it will hurt.

I have parts for your superturbo. Turbine is actually from some Cat so they should fit fine, have also CNC file for both turbine and compressor so you dont need to trust some idiot handmachining them to US tolerances.

 

[SmokinCAT]

Can’t wait until my cabover Volvo shows up.

RigWrench is sourcing me a European super turbo and special tune to run it.


Until then I’ll just clean this turd.

FYI a 6,000rpm grinder will chuck a polishing brick Mach 2 into your shin and it will hurt.

They have been on there long enough now that truck wouldnt even look right anymore with round holes.

 

[jfaulkner]

I have parts for your superturbo. Turbine is actually from some Cat so they should fit fine, have also CNC file for both turbine and compressor so you dont need to trust some idiot handmachining them to US tolerances.

CNC? We don’t CNC parts here, everything is whittled out of a piece of oak. We’re not as advanced as Finland. I actually don’t know where we would be as a society without all the amazing things to come out of Finland. I remember back when Sven was the first to orbit the earth followed by planting that flag on the moon.