Recent content by 94 12valve

I'm selling my 11 blade billet s480 that I pulled with this last half of the year. The only reason I'm selling is its too big for the class I want to pull in this upcoming year. Its got the heavy duty 360* thrust bearing, billet 11 blade gtx style comp wheel, 96 turbine, in a 1.32 t6. Turbo is...

I bought this turbo in April this year ran it for 12 hooks. Has no in and out shaft play and side to side in normal. Charger was always cooled down before shutdown and has only had Aimsoil ran through it. Specs NADM legal 2.6 charger ED's 75mm 6 blade billet compressor wheel .66A/R compressor...

I need one to replace the 23 spline input I have now Thanks

I'm selling the turbo I ran all last year on my puller it meets NADM 2.6 class rules. It ran very well on my stock piston/ stock valve motor, the only reason I'm selling this charger is to go a little bigger for this year. The charger is at ED now, there going through it to make sure everything...

I have two ARB air lockers that I no longer need. First one will fit a dana 60 4.10 and lower, will also work 4.10 and up with a ring gear spacer. 30 spline. 550+shipping The second will fit a Dana 80 4.10 and higher 35 spline 550+shipping. also have a set of ring and pinions for a dana 60...

I have a 4.88 ring and pinion gear set for a d80 and a d60. The ring and pinion gear for the d60 was never ran or installed. The gears for the d80 were installed in a spare rear but never ran. I'll take $700 + shipping for both sets Dave

I have a 5" aluminum air shut off made by ED. Comes with 2 rubber hose connectors and two worm clamps. asking $300+ the ride.

Well, I had to pull my 241 DHD out of my truck this week because I could not run high range. Low worked fine but as soon as I shifted into high range the case would disengauge and act like it was stuck in netural. Tore into it and found I had bent the input retainer ring and blew the sealing...

I have a used ED T3/T4 adapter. It was on my truck for 1 sled pull and 6 dyno runs before I upgraded to a T4 manifold. $50+ the ride Exhaust housing off of a s465 with a 74/83 turbine wheel T4 foot .9 A/R. In very good shape. $100+ the ride Stock 12v exhaust manifold $30+ the ride

I'm selling my 50mm ED gate, has a t4/t4 adapter, and a steel connector tube. I put a bigger turbine housing on my charger and no longer need this gate. The gate works as it should, comes with an adjustable boost elbow, flex pipe with V band to connect to your exhaust down pipe , and a set of...

"Diesel pulls sunday 6/27 at stem o roma Windsor Pa Starts at 10am I would say be there by 830 for tech. Interstate tractors there as well. Having decent cash pay outs" Who's goin? I plan on making the trip, was told the same rules as last time would be used.

I would like some prices on a set of 4.88 gears for my puller. They will be replacing my 3.54's so I will need a pice for all the peices to make this swap work. Thanks Dave

I'm looking for a set of 4.88's to replace my 3.54's. I'm looking for everything needed to make this swap work. Thanks Dave

I'm selling pretty much my entire valve train all items were bought new and broke in with ZDDP. All items have 2000 miles on them, also I have only run full synthetic oil for all 2000 miles. I have a HD Cams Big Stick that I bought new last year with a 107 LSA. Cam comes with the cam gear and...

I am looking for a set of 181's, 191's, or a set of .024's to replace my full cuts. After I upgraded to a scheid pump the full cuts are just dumping way too much fuel.I will be selling the full cuts after I downgrade Thanks