Recent content by Drasko

I'm looking for a t4 12v steed speed, preferably used unless someone has one in stock. Poulinas sold while i was in the middle of nowhere at work unfortunately so I'm still looking. Thanks Drasko

6.7 cummins/ manual transmission/deleted 247k miles $8500obo I originally purchased this truck to have another daily driver/fun street truck but 4 trucks in the driveway is too many. I figured I'd drive it more but i haven't, so it has to go. Title: Kansas clean, clear, and in my hand This...

does anyone have a rclb 2wd auto truck that could measure the driveshaft for me from center to center of the u-joints? Im hoping it's 60-61" so i can use it in my fummins swap. Thank you Sent from my SM-G930T using Tapatalk

Im selling my aeromotive belt driven lift pump. Ill also includes the mounting bracket and drive hub that mounts on the crank. It flows a major amount of fuel. You will need to make a mount for it as there's no bolt on application from aeromotive. I had mine mounted where the ac compressor used...

Im looking for a used billet input like the one i just missed on here. Lol Please let me know what you have. Adam draskovich

I'm in the market for a used billet input for a 47re. Adam

I know the Cummins manual doesn't mention using it besides at the bottom where the oil pan gasket meets the timing case gasket. Does everyone use rtv on each side of the timing case casket between the block and timing case? This is on a fresh rebuild.

I have the block back from the machine shop and am FINALLY about to build the engine for this never ending project. My main question is do i do ARP main stud and rod bolts or go with new standard cummins bolts? whats the limitations for the stock bottom end? im thinking stock bolts will survive...

As stated in the title, i have an unneeded nv4500 bellhousing. $300 shipped to anywhere in the lower 48. Ill get a picture up of it tomorrow. Paypal accepted. Adam Draskovich

I'm getting ready to build my 12v for my fummins once I get the block back from the machine shop. I'm figuring I'll be around the 600hp range with a 351/475 set of twins. What's the normal opinion on bolt replacement on the main caps? Is there a theory or written rule on when to replace the...

I picked up a 2wd nv4500 for my fummins until I build an auto. It was supposedly rebuilt not all too long ago. It seems like the tailshaft has quite a bit of side to side play. Is this normal? Tomorrow, ill see if I can measure how much. This is the only 2wd vehicle I've ever owned in my entire...

I've been searching and reading until my eyes started bleeding and have yet to come to a final conclusion. I'm building what most guys here would consider a mediocre set of twins. The plan is an he351 with the drilled out wastegate to roughly 1" over an s475 I picked up last night. The 475 came...

I'm looking at a set of 20x10 raceline havoc wheels for my 99rclb 2wd. I'm trying to figure out this stupid wheel offset vs backspace issue. They have 2 sizes available, 20x10 -12offset 5" backspacing or the 20x10 -24 offset with 4.5"backspace. I'm thoroughly confused if the backspacing listed...

Hiya Jeff, I have finally attained a good 12 valve block for my cracked one in my fummins. I have some .20 over non intercooled pistons from Mark Nixon I'm planning on getting so I need a complete rebuild kit for a12v with .20over rings wrist pinsand all but no pistons. Also I'm not sure on...

I'm selling off a dana 60 and dana 80 set out of a 1996 ram 3500. they've been sitting for a while. they have 3:54s and limited slip with drum brakes on the 80. I'm asking $550obo for the 80 and $450obo for the dana 60. as a set, I'd go $900obo for them together. These are located in Edgerton...