Recent content by RAB 38

2005 Ram Laramie Sport 4x4. 700+ hp I am the original owner and ordered the truck optioned out. power everything. Does not have a sunroof or power adj. pedals. 201,000miles Performance; 80% over Exergy injectors, BMS 85% II CP3 Arp studs Oringed head Heavy duty valve springs Engineered Diesel...

2005 Ram Laramie Sport 4x4. 700+ hp I am the original owner and ordered the truck optioned out. power everything. Does not have a sunroof or power adj. pedals. 196,000 miles Performance; 80% over Exergy injectors, BMS 85% II CP3 Arp studs Oringed head Heavy duty valve springs Engineered Diesel...

Looking for a duramax donor truck for my 72 blazer. I want to convert it over to a duramax so I need a complete engine, trans, wiring harness and ecu. I have been searching online and I am having trouble finding anything reasonable. If someone knows of a good place to find one let me know...

Thinking about converting my 72 blazer over to a duramax. I don't have room to put the Allison behind it so I am trying to figure out what trans and transfer case options are out there. Does anyone have the length of a duraflite or a 4r100? These both seem to hold power and I believe are...

Went to the opening night of midnight madness at maryland international raceway last night. This year they have a diesel truck class. Pretty good turn out, I think there were around 50 trucks. I ended up being number 2 qualifier with an 11.84. And went a fastest of 11.76 @114. Got a few...

I am trying to help out my neighbor with is 07 6.0. He has no gears, he was driving and it shifted really hard a few times he said and when stopped at a light it wouldnt go any more. Towed it home and it seems like the clutches are gone. There dont seem to be any codes or anything so I am...

MP8 fits 04.5-05 dodge cummins. Used worked fine when I took it off the truck. $250 obo

Has any one else had problems with their firewall insulation falling downor coming loose from the firewall? What solutions are out there? I don't want to just remove it, is there something to replace it with that is better if I just cut the bad section out?

I pulled my head because what I though was a blown head gasket. Pulled the head and did not see any signs of it being blown. My head is oringed and my question is do I need to have new orings put in the head or can I just put a new gasket on and reinstall the head? I tried to check the...

Hx40 16cm over ht3b 26 cm twins. Blue powder coated pipes comes with oil lines, coolant lines, new afe filter, 5" down pipe, ats manifold. fits 3rd gen. Turbos are tight. Everything is boxed up ready to go. $1800 OBO

I just got one of these to replace my 60 psi gauge. I hooked it up per the instructions but it will not light up nor will it read boost. I have a good ground and power at the connector. I also have power to the dimmer wire at the connector. Anything else to check or is it the gauge?

I put on my coolant bypass this weekend along with my twins. I have had this bypass for a few years just never got around to putting it on. I believe it is his first generation system. Anyway, I have noticed that now it's on the truck does not get to operating temp. Seems to run around 150-160...

I was trying to help a friend of mine today with his 04 cummins. He has a predator pressure box and a super chips tuner. He is having a surge or stutter any time he runs the super chips or when he runs the predator past 40%. I replaced the fca and that didn't change anything. I don't think its...

I started on my new setup tonight. Installed a industrial injection 85% cp3. Got it on and running, took it for a short drive and I could really feel an improvement in throttle response. The rest of my parts should be here over the next few weeks. My exergy 80% (150 hp) injectors should be to...

Just ordered some new injectors, I have read that you should replace the connector tubes when installing new injectors. I have had my original ones out 3 times and reused the tubes each time. Where is a good place to get them?