Search results

replacing the hpop on a 03 6.0L...anybody know the tq specs for the hold down bolts? thanks

i am wokrin on an 03 6.0L and was just wondering if anyone knew where might the best place to get a new HPOP for it. i know the 03's and 04's had issues with them and i was curious to whether anyone knew if there was anyone that builds an upgraded HPOP or if i should just go go through ford for...

156,000 miles on both nothing wrong with them crank and cam gears on them already. $250.00 for crank $200.00 for cam

just pulled off of truck with 180,000 miles. has valves in them includes exh. manifolds and up-pipes lifters, pushrods, and valve cover gaskets/injectors harnesses $300.00 for both heads.

truck has 136,000 miles on it, and still has the factory hpop on it. i'm guessing that is what is bad. driving it down the road, pulling a nurse tank full of liquid fertilizer, it lost a bunch of power. changed oil and fuel filters on it. didnt make any difference, in fact i noticed it getting...

hey guys, i am going to be installing 90hp injector nozzles on an 04 cr, is there any adjustments i have to make to the injector for the new nozzle? such as pop off pressure?

rebuilt the engine and has good oil pressure, but i am not getting oil up to the turbo charger. fried one turbo, so i pulled it off and ran it without the the turbo for about a minute and had no oil pumping up to where the turbo mounts. anybody have any ideas what could be causing this?

180,000 miles cylinder heads, with injectors, rocker arms, pushrods, valve cover gaskets/wiring harness, high pressure oil pump, timing cover, and top resorvoir with top cover. *heads and injectors have not been checked out* however engine ran great before pulled. i would highly recommend...

all engine parts came out of same engine with 197,000 miles on it. crankshaft-$300obo camshaft-$100obo all 8 connecting rods-$300obo 7 pistons-$100obo (one piston broke the skirting, nothing inside engine was hurt) lifters with guides-$50obo

got a turbo off a 96 7.3L. wondering what it might be worth? has 180,000 miles on it. any suggestions?

i have a 2000 F-650 with a cracked engine block. is a 96 7.3L and the 2000 engines the same, or atleast the engine blocks the same?

i got an 03 6.0L. i checked the oil in it the other day and it was 2qts. low....so i started checking around on the truck and found oil is coming from the left side valve cover through that tube that connects to the air intake tube to the intake side of the turbo and it is blowing oil into my...

hey guys, i gotta a 03 6.0 and the fuel pump on the frame all of a sudden got louder. now i'm a cummins guy and aint real familar with the 6.0 yet. my ol' man has the 6.0. i think that its a sign of the pump may be going out sooner or later. you can hear the pump runing while your drivin it down...

hey guys, i gotta 01 cummins i just put a edge drag comp and bd rad in and my volt, oil pressure, water temp, and fuel gauge don't work. i also put in an airdog fp-150. i'm certain everything is wired up right but i'll check it all out again. all my fuses are good too. my tach works too. don't...

a guy called me and said that it just falls on its face when he accelerates and its really bad when it shifts into a higher gear. he said it smokes a little bit of white when he accelerates as well. i told him it sounds to me like it could be an injector or injectors. but with a 7.3, it is hard...

does anyone know if you can run bio diesel in an 03 6.0 powerstroke. i race a cummins but my dad has an 03 6.0. i'm not real familiar with the 6.0 yet. will it have any affect on the injectors or anything else. ( i doubt it will hurt anything, but i figured i better get another opinion). thanks...

Has a 351w that don't run, c6 2wheel drive trans, has dana 60 rear full float axle with 4.10 gears, van is complete. just needs engine work. engine is not tied up. would make a good work or play van. make offer.

60 rear full float 8 lug with 4.10 gears. came out of a 1986 E350 van. asking $300 obo

tires are 50 to 75% tread and their on mickey thompson classic 2 rims. asking $700 obo

1977 351 windsor bored .30 over, xtreme 4x4 comp cam and lifters 496/512 lift, edelbrock performer rpm aluminum intake manifold, hooker competition headers, brand new crank, high volume oil pump, high compression pistons, cylinder heads were completely redone with new vavles and seals, ARP...