Search results

Hey guys, I haven’t posted in forever but looking for some opinions on a truck we just bought that rides like a rubber block truck. 07 9900, it is 260ish wheelbase with 12k front and has a Hendrickson HAS rear suspension. Replaced height valve, set height to Hendrickson spec, replaced...

I recently purchased a trailer with dexter 15k oil bath axles that the previous owner converted to grease. Going to pull everything apart and replace bearings/races and considering switching back to oil due to ease of maintenance. Is it worth dealing with the potential for seal failures with...

BBI injectors Stage 1 with approx 22,000 miles on them, just tested by source automotive and they were all on par with what they were when built. Filtered with 2 micron fuel since new. About 24% over stock in size. Enough fuel for 650hp with a super clean/smooth idle and midrange. Don't need any...

We're looking to buy our first semi, found a pretty straight low hour pre emission Series 60 in a Sterling chassis. It has 4.56s and a 18speed, from my reading this is really steep combination. Is it an option to do a gear swap or should I move on to a different truck? Truck will be 90% highway...

Could someone send me a Clean factory tune for a 06 Auto with the high idle enabled. PM me for email address. Thank-you.

Does a 67 have a pressure sensor for the crankcase? I've read on another forum about being able to see the pressure values on a scanner but I don't remember noticing a sensor anytime that I've switched ccv filters... Thanks

Looking for a 2006 ECM, Engine Harness and Accelerator Pedal. PM me with what you got.. Thanks,

Now I've seen my share of CRs, but never something with this. The truck seems to be all stock and the owner says he bought it like this...

Does anyone know on a 48re, When the ATS lockup controller hits a value to command lockup, is it a direct ground or is it pulse with modulated? Just trying to eliminate some variables.... Thanks, Jade

Hello, we're planning to make a pulling track where there is mostly a sand base, there is some clay mixed in but not a lot. What can be expected for a track that is sandy? What would the best track prep be? Trying to make the best track with the area we have, thanks for the help. Sent from...

I'm looking for a 38 spline spool for a Dodge 11.5. PM me if you got one!

Hi, I purchased a Raptor 150 from Glacier Diesel and it came with the quick connect fittings. I would like to ditch all the quick connects because I'm running a fuel sump and braided lines from the Raptor to the Cp3. My 1/2 NPT will not quite thread into the Raptor pump, what is the Raptor...

So...I bought some nozzles for a 04.5-07 CR and today I went to swap them to my current nozzles in my 05. The 'factory' nozzles I have seem to be a different design than the aftermarket ones. Plus I was not expecting the puck/sping/spacer to be in my current bodies(I thought this was only a 6.7L...

Does the air sensor in the factory intake(right after the filter box) need to see airflow to function properly or can I just leave it plugged in and hanging? Everyone I talk to has a different opinion... Thanks:charger:

I need the bent metal coolant pipe that routes over the top cp3 and back to the radiator. My kit is a II but I think parts from mostly any kit would work. Let me know, I would need this stuff shipped next day air to Canada. Thanks!:Cheer:

I have a Smarty Jr for a 03-07 5.9L for sale. $430 including shipping. Paypal only. MADS Electronics - Smarty - CaTCHER - Smarty06 :thankyou2:

Found this attached to the pan magnet in a 48re, thoughts? Sent from my iPhone using Tapatalk

My turbo on my 01 has quite a bit raw oil / carbon in the compressor housing and wheel. It seems to have quite abit up/down play but no in/out. Should I start looking for a different turbo? Running a paper BHAF for a filter. Here are the pictures: Thanks Sent from my iPhone using Tapatalk

Besides the price, why are roller rockers not a popular option in performance engine builds?, or are they just used by the quiet few?. Are there benifits using them with a sub 4500rpm engine?. Just curious after seeing them on Pure Diesel Powers website, search didnt come up with much. Cummins...

Check out this video of a friends 06. Engine hot, low mileage, idle. http://www.youtube.com/watch?v=Wauq9OSbhEM&feature=youtube_gdata I would say this is a little much, eh?. Truck runs fine.