Search results

Brand new 2nd gen 12v/24v Gorilla girdle with A1 12mm XL main studs. Girdle and hardware are still in the packages. The A1 studs were installed in a block, torqued to 30 ft lb and then removed in favor of a 14mm setup. Will fit all Encore blocks. $750 shipped D60 front axle out of a 95 with 4.10...

Brand new, never installed Gorilla Girdle w/hardware. A1 12mm XL mainstuds. Studs were installed and torqued to 30 lb/ft and then removed in favor of a different setup. I bought this kit for a 2nd gen 24v but was told that it will fit all Encore blocks. I wasn't sure about the scribbles on the...

I bought my truck with the flatbed on it and whoever wired the lights on the bed hooked them to the trailer light harness and now my "Lamp Out" light is on all the time. I'm looking for the plug on the bed that would plug into the main light wiring harness that comes from the cab. I need just...

I've got an 01 engine with 10k original miles on it. Engine is complete minus the turbo, injectors and vp pump. It has full engine harness and ECM and has the bellhousing adapter bolted to it as well. I bought it for a project and never used it. A friend wanted the black valve cover off of it...

I've got a full billet HTS 47re trans with deep pan. Trans has 19 hooks on it since rebuilt by an authorized Goerend installer. $2500 Goerend triple disk converter also with 19 hooks since freshened and restalled by Goerend. Converter is set for 3400 stall. $850 Billet flexplate in pic is...

Front tires are chopped on my truck and I've got a chance to get some descent used tires but they are 1" taller then the rears...1" difference gonna bind things up? Or is that not enuff difference to worry about? Rears are only a few months old so im not replacing them. Truck is an 04 Dodge...

01 24v engine with wiring harness and ecm. 10k original miles. No turbo, VP pump, injectors or AC pump...everything else is there. $2500. Full built/full billet HTS 47re trans with deep pan. 19 hooks since freshened up and 0 street miles. Goerend triple disk converter with 3400 stall also with...

A set of Scheid Lightning 24v 6x18's set for ppump pop off. I purchased them from Jamie at CPP to put in a 2.5 truck that never got finished. I think Jamie said the injectors had around 20k on them when they were pulled. $700 shipped.

Dual wheel drum brake D80...I purchased a used spool and then bought a new set of Yukon 4.11 gears and a new Motive Gear master install kit and had them installed in the housing. The axle tubes have also been welded. Everything in the center section is brand new except the spool...which was...

2000 24v engine with 10k miles on it...yes, 10k miles. No vp pump, injectors, turbo or AC pump...everything else is there. Has wiring harness and ECM also. $2700 180hp 12mm p-pump benched and freshened up by Kevin at Northeast Diesel. 0 fuel plate, full cuts, mack rack plug and 5k springs...

First off, I'm a p-pump newb so kinda lost to start with...always had a vp pump. Building a 2.5 truck and need some opinions on what I need to obtain my HP goal. I've got it in my head that I wanna be around 800hp. Here's my thoughts and I'm not sure if I'm on the right track or not. I found...

I have a good 2nd gen ex. manifold and an HY 35. Motor has @ 10k miles on it (yes you read that right 10,000). Manifold for $135 shipped. Turbo for $185 shipped. Or can deliver to Scheids on Sat. for $100 (manifold) and $150 (turbo).

I have three 4-hole wheels and one 7-hole wheel...all with tires but the tires are not worth much but could probably get a few thousand out of them yet. Also have 2 rear hubcaps and one front hubcap. Hubcaps are in good condition with a few blemishes...they are just dirty in the pics. These...

95 12v engine...IH Casting. Was told it had 270k on it and was running when removed from truck but previous owner said it did have some blow-by. I have valve covers and a few small misc. parts to go with it but other then that what you see is what you get. $800 or reasonable offer. Can...

BullyDog PMT...as far as I know it will fit 03-10 6.0L & 6.4L Powerstroke**01-09 6.6L Duramax**03-10 5.9L & 6.7L Cummins. Comes with an SD card and suction cup mount and pyro. I downloaded the latest software on it last summer when I hooked it up. $575 shipped

I have a 95 12v engine...IH casting. It is the complete bottom end and complete head only...the engine is missing everything else that bolts to the outside of it. I was told that it had 270k on it when I bought it. It looks like it could possibly need to be bored...maybe just a good hone job...I...

Got a stock 47re with cooler lines and a stock TC. Guy I bought them from said they had around 170k on them and worked before removing them from the truck. I was gonna build it but bought a built tranny instead. $450

Complete 47re with cooler lines and a stock TC. I bought this from a guy who was parting out a truck. Supposedly had around 170k on trans and TC and supposedly worked before being removed. I bought it with intentions to build it for my puller but bought a full built tranny instead. $475...

I have a used set of 9004 HID's...color/heat range 6000k. This is a Bi-Xenon (high/low beam) kit. 6000k is a white light...last in the white color range...right before you go to blue. Comes with HD wiring kit which feeds power from the batteries to run the lights...lights are still controlled...

NIB MOOG upper and lower balljoints...non greasable. I also have, still in the box, all brand new tie rods and tie rod ends. The only one I don't have is the tie rod end that hooks to the pitman arm and runs to the adjusting sleeve. WILL FIT 01-02 ONLY!!! Paid over $435 new. Will sell for...