Search results

I finally have the front and rear ride height set on the prostreet truck im building. What im wondering is if any racers have some input on what kind of pinion angle I should set my truck to. As well as a good starting point for the 4 link bars. The rear setup is a chris alston chassis works...

I'm got a 93 truck i'm working on that has a leaking ksb. Its leaking fuel around the flange between the two torx bolts on the bottom. My question is can you pull that and reseal it with out pulling the pump? And if so does anyone have a part number for the seal that needs replaced. Thanks for...

Need to sell my 97 singlecab The truck has a 98 motor in it with 150k on engine, Head has been o-ringed has new valves and valve seals with a custom 5 angle valve job, and is held down with 12mm ARP studs. Has 5k miles on head work. Truck has a 12mm 215hp pump that has been benched and maxed...

Not sure if this is a repost or not but Rudy is putting on his second annual dyno and track day on March 17th at piedmont dragstrip. We will be there with our mobile dynojet 224 along with drag racing all day and a sled pull that night. Event kicks off at 10 a.m. but as soon as we have trucks...

What are you guys doing to delete the fuel bowl on a 6.7 cummins truck. Is there a kit available. I did some searching but didn't find what I needed.

Not sure if this has been gone over before but I didn't find anything after searching. I swapped a 241dhd t-case out of an 02 into in my 97 dodge, as most know there was no way to hook up the speedometer. After some research I got ahold of dakota digital and hooked up there SGI-5c box. It takes...

I have a garrett gt4294 turbo with a 67mm compressor and a t4 1.0 housing. I would like to trade it for an s300 with a t4 mount as i'm wanting to go to twins. Turbo has less than 5k miles on it with no play.

I am putting on a dyno event on the 16th in greeley, co at Weld county garage. We were tossing around some ideas on how to get more people to come and thought maybe a jackpot would be good. The thought was 25 dollars to enter the jackpot all money goes back to the competitors. Winner gets 70%...

370 marine injectors need to get rid of these. 250.00

My steering wheel is starting to come apart and loose all its foam and its time for a replacement. Are there any aftermarket options available any one on here has tried? If so where did you get it?

There was some talk at the event that numbers were lower than expected on alot of trucks at our event. Even a truck we took dynod far lower than its normal numbers. I have been looking into this all morning with dyno jet and I hate to say our brake was hanging on the drum due to low air pressure...

Any options for a t4 exhaust housing for a k31 turbo with an 85x76 turbine wheel.

This truck came into my shop the other day with a motor that wouldn't turn over. Upon further inspection I found the #6 piston damaged. I removed the head and found this. The timing was recently set else where. I haven't measured it yet as I got it apart right at the end of the day. But it...

I need a v band clamp to attach to the outlet of the exhaust housing of a gt4094 T4 housing. I've tried talking to garrett and they said they didn't have one to sell me and to look at aftermarket. So does anyone know if the 3 inch clamps from racepartssolutions will fit this housing? I have the...

I'm working on a commonrail with dual pumps and the second pump has the shaft seal leaking on it. It is a duramax pump. Is there a way to get that seal and replace it myself or is this thing gonna need to go to a pump shop? Any help is appreciated.

Our pulling association here is allowing twins in the classes. They will only be teching the atmoshere turbo as a 2.6 So just wondering what you guys think of doing a 66x65 with 13cm housing over like a 66x74 with a 16cm housing. Would it work?

I'm getting closer to needing a roll cage in my truck. I was gonna do it myself but i've come to realize that its just something you can't skimp on, and it needs to be done right. So does anyone know of a good fab shop in the colorado or nebraska area that will fab and install a cage for a pickup?

I'm gonna be at worlds this weekend in topeka would like to get rid of these turbos there. First one is a HTT 66 with the 71 turbine has some play but doesn't touch asking 1000 or best offer. I also have a brand new HT3b with a 32cm housing and t6 flange just want it gone asking 500 or best...

I am in need of an nv5600 six speed trans. If anyone has one or knows where to get one please let me know.:Cheer:

Need some help tuning my truck. Truck is a 97 12v, 215 pump no plate stock afc with star wheel set really tight. Timing at 23 degrees. DDP delivery valves with 5x18 injectors 145 degree spray pattern. With .093 haisley lines. Truck has twin turbos with a super b special on top and an ht60 on...