Recent content by okish

  1. O

    Gated 65mm s300 turbine housing.

    Looking for a gated 65mm exhaust housing. Let me know what you have.
  2. O

    External wastegate on only 1/2 the cyl?

    Due to packaging reasons, it would be extremely easy to run a gate on only the front 3 cyl of the manifold. I don't see this as an issue, but if there is one, I still can put it in the collector and gate both runners, it would be alot more work of course. Gate is. 44mm jgs and top turbine...
  3. O

    S369sxe turbine housing size when used in compounds

    Just picked up a s369sxe from a fellow members and will be using it as my primary in a set of small compounds on my 02. The secondary will be a s256 with a 65mm turbine wheel and .85 housing, it will be wastegated with a 40mm jgs gate into the hot pipe. The s369 has the 73mm turbine wheel. It...
  4. O

    Stock 2wd 47re good as is or as a core

    Pulled out of my freinds wrecked 97 12v. Was running and shifting just fine. It's an all stock trans with a goerend rebuilt overdrive section. You can use it as is on a stock truck or as a good core. Valve body was loosened to drain fluid for storage and it has no filter installed. Fluid was...
  5. O

    Wanted: 91.5 to 02 cooling fan

    Looking for a cooling fan for a 91.5 to 02, shipped to 94590. Will buy with clutch and shroud if you have them.
  6. O

    K31 compressor shaft nut torque

    Anyone know what the torque spec should be for a k31's compressor nut? I looked high and low and couldn't find diddly.
  7. O

    Brand new 16cm HX40 wastegated turbine housing

    I have a new hx40 16cm wastegated turbine housing, t3 flange and comes with the wastegate actuator. Asking 150 plus shipping. I'll put up some pics in a bit, been sitting on a shelf for about 5 years but never run.
  8. O

    What shifter, Hurst quarter stick or B&M pro ratchet

    Well, im finally sick of my column shifter after hitting neutral one too many times. I've actually got a hurst quarter stick and a B&M pro ratchet in my possession but have never used either because the only auto i have is my truck. Any opinions on either? the B&M looks to be better quality.
  9. O

    Anyway to get rid of a pesky p1740 code?

    Is there a PCM reflash available to get rid of this p1740 trans code? I have a pretty tight 89% dtt billet super single and it pops that code about once every 2 weeks. I don't drive my truck hard all the time so thats probably why the computer thinks there is not enough drop in rpm's when it...
  10. O

    Grand national i'd drive.

    Not sure if its been posted before.... but Diesel Grand National Diesel Grand National
    • okish
    • Thread
    • Replies: 13
    • Forum: Video
  11. O

    Using wierd sized k31 as primary charger?

    Anyone think that this Help ID a weird BW turbo? - Competition Diesel.Com - Bringing The BEST Together k31 will make a good primary under a 62/68? I just want to make sure the turbine will flow enough on it.
  12. O

    power-lok case for my d70

    Looking for a 4.10 and down power-lok case for my 02. im sick of one wheel peels in 2wd.
  13. O

    64mm 10 blade s300 turbine wheel?

    I thought all 64mm/76mm s300 turbine wheels were 11 blade, 71mm wheels had 10 blades. The s300 on my 02 has a 10 blade 64mm wheel on it and the htbg that i also have has a 11 blade 64mm wheel.... is there any benefit for either?
  14. O

    Cleaning up cruising/low boost smoke.

    I'm looking for ideas on cleaning up low boost/cruising smoke on my 02. This thing is almost undrivable on the street due to the smoke, you can see the smoke rolling out of the tail pipe just cruising around at low boost 5-10 psi. i have no idle haze and the smoke cleans up past 25-30 psi...
  15. O

    Picture of coolant pipes with 3pc manifold.

    I need a pic of how the coolant pipes are done with a 3 pc exhaust manifold, specifically a pdi manifold. I dont have the install kit nor instuctions and i just want to see what modifications need to be done to the pipes.
See more
Back
Top