Big Single Questions

[Timebomb]

All my rods always went out the exhaust. You should look into a ht4 turbo

I agree, an HT4C would work well.

 

[Ragged Edge]

Saw 6950 this year on an auomotive governor, a mishap between two pump shops working on the same pump and we lucked in to it. Works very well.

I would say jump up a gear. You dont have any power up that high anyway

 

[CurtisEmery]

Junk and Junk is what Ive heard from those turbos. If I run a Garrett I will run the GT4202R. Its a few steps back obviously. But think its the best 3.0 charger available. Just dont know how it will stack up in an unlimited single class for NADM

I would also take a look at what Turbonetics has to offer. They make a Y2K in 78,80,82,88,91mm inducer. T6 foot and lots of turbine/housing options.

 

[2Tone12V]

I would also take a look at what Turbonetics has to offer. They make a Y2K in 78,80,82,88,91mm inducer. T6 foot and lots of turbine/housing options.

Nice turbos but Im not going to be the tester for them. Havent heard to much of anyone running them. I have heard the HT4C. How bout some info on it. Who makes it and all that good stuff. Half the stuff ends up off the turbo anyhow and replaced with new housing and stuff. Whats it take on the charger?

 

[2wpuller]

I have one sitting here if you want to stop by and look at it.

Dale

 

[2Tone12V]

Good charger or no Dale?

 

[2wpuller]

Yes it good charger.

Dale

 

[2Tone12V]

Whats your pick on an unlimited single Dale?

 

[2wpuller]

I have to do some thinking on that.Alot of it depend on price to me at the moment I paid $1000.00 for the HT4C
3 years ago.Was going to put it on my brother truck for twins.It has a 3.3 or a 3.4 compressor I don't remember on the ex,wheel but it has a 26cm housing.


Dale

 

[SmokinCAT]

I was wondering, is there any way to figure a correlation between inducer size and maximum air flow. I am buying a charger in th next few months, and I am debating on what size inducer to go with, right now I am thinking of going with a 100mm inducer, but can go up to 106mm if I want to.

Anyone have any idea of how much airflow difference there would be between the two?

 

[2Tone12V]

I was wondering, is there any way to figure a correlation between inducer size and maximum air flow. I am buying a charger in th next few months, and I am debating on what size inducer to go with, right now I am thinking of going with a 100mm inducer, but can go up to 106mm if I want to.

Anyone have any idea of how much airflow difference there would be between the two?

Depends on your mods and stuff. What class you hooking in. By the way Dale. Got my charger all taken care of!!

 

[not enoughsmoke]

Dont Waste Ur Time On Singles Go Twins And U Can Still Drive It On The Street

 

[2wpuller]

Depends on your mods and stuff. What class you hooking in. By the way Dale. Got my charger all taken care of!!

Cool what did you end up getting:charger:

Dale

 

[2Tone12V]

Cool what did you end up getting:charger:

Dale

Sent ya a PM Dale

 

[SmokinCAT]

Depends on your mods and stuff. What class you hooking in. By the way Dale. Got my charger all taken care of!!

This is for my semi, I pull in a street class, which is gonna take over 1000hp to win/compete.

Im currently running a 3 inch charger and I am hitting full boost (40psi) at about 1600rpms, I have more fuel than it will stand and I plan on adding more.

The only thing I know for sure is how big my injectors are (6x.020) and they flow alot.