Recent content by dieselracer07

I'm looking to buy a TDI, and I'd like to get some feedback on them. I'm leaning towards a 2005-2009 Jetta, preferably with a manual transmission. What kind of things should I look for when buying one? What kind of mileage range should I be looking at? I want to find one 120,000 miles or less...

Batmowheel 75/87/.90 T4 foot. Unsure of exact miles on turbo, but it has no play and runs great. Compressor housing is powdercoated chrome. V-band flange welded on. Only reason for selling is to go to compounds. Can include the S400 outlet elbow and clamp and also the 4&5/8 downpipe flange and...

I'm swapping out the rear axle in my truck tomorrow for one with 3:54s. I'm not familiar with the speedometer function on these. Will it read right with this axle? It still has the sensor on the chunk. Sent from my paperweight

I haven't torn the engine down yet to inspect the internals, so I'll post those later. The block and crank are already spoken for though. Shipping is on the buyer's dime. If any of the prices seem out of line, make an offer. Located in South GA. Tappet cover- $40 Timing case- $100 Timing cover-...

I want to convert mine to a full manual valve body and am curious as to what kits people are using. Has anyone tried this kit, what all does it consist of, and how difficult is it to install? http://transmissiontechnologies.com/500-518-618-46re-47re-full-manual-shift-kit.aspx Sent from my...

Brand new, all 8 arms, I can powdercoat them any color you want. I don't have any pictures of one with the 5", but here's one with the 8". So just imagine 3" less. Will clear 34" tires. Sent from my paperweight

I have the kit that pure diesel power sells. I used it one time, and it's been sitting in my toolbox ever since. I want to keep the gear puller. Other than that, everything else is all there. Sells for $169+shipping. I'd like to get $130 shipped...

Mine has a groove cut into it that is eating up the seal and pouring gear oil out. I don't have a much to spend at the moment. I don't mind if the u-joint is shot out. I have a spare. Sent from my paperweight

Are any of you running the free spin hub kit. If so, how do you like it? What kind of mpg increase did you see? I'm looking into them. I'll probably get a posi lock kit for now, until I save up for the dynatrac. My actuator isn't working right. For now, I locked the fork in the engaged position...

This has been on my truck for about 2500 miles. I'm putting a FTE resonator on, so I don't need this anymore. Not sure what they sell for so I'll start at $70+shipping Sent from my paperweight

Finally took my truck to the track today. Didn't have a front driveshaft so all passes were in 2wd, and it was a slip and slide the whole time. Truck weighed in at 6810 pounds. My ET was terrible. I had to back out of it so many times to get traction again. I also couldn't get it to go into OD...

These are currently in my truck. They run fine with no lope. Only reason for selling is to downsize to a set of 025s. $160 shipped. Sent from my paperweight

Now for another aggravating issue with my truck.... This engine has less than 2500 miles since a complete rebuild. Once it is at operating temp it will occasionally drop oil pressure. It only happens once coming to a stop or putting it into reverse and doesn't do it 100% of the time. It...

Well fellas, I've been trying to track this issue down and have had no luck so far. I'll list what's done to the suspension and brake system first. I have all new Moog T-style steering components, new Moog ball joints, new Precision hub assemblies, new rotors and pads and calipers, BD adjustable...

I have a new Ultima starter. Part# 33361. It has a lifetime warranty. Sold the Duramax awhile back and have no need for it. They are 189.99+core at Oreillys. I'll take $170 shipped. Sent from my paperweight