Search results

We are looking for high quality videos and photos of your Valair equipped trucks for our video montage at the 2013 SEMA show. We are looking for a wide variety so anything goes as long as you are running a Valair clutch. Towing Playing in the mud Sled pulling Drag racing Dyno runs Anything...

2003 Dodge Ram 3500 5.9 Cummins Motor built beginning of last season Hamilton cam, Pistons cut .060 for clearance 75lpm injectors SS bodies Wicked Diesel Dragon Slayer CP3 ED 2.6 S400 billet wheel, T4 ex housing 06 standalone ECM with EFI tuning by Dans Diesel Performance Intelladash Digital...

Just thought I would post this up and see it someone had one laying around before I buy a new set up.

I have a smarty SSR for sale. $500 Will possibly trade for 7.5R18 tractor tires and dodge 8 lug 18" wheels

I need help finding a source for a few torx sockets. Looking for the following: IP45 Torx Plus IP50 Torx Plus IPR45 Tamper Proof Torx Plus (5 point with pin hole) IPR50 Tamper Proof Torx Plus (5 point with pin hole) I used to get the tamper proof from snap on but there are now out of...

If we ran a stock block, rotating assembly, pistons, and added all the mods to run 5000+RPM.. (valve springs, cam, fuel, air...) how long would the lower end last.

Lets get wasted, get hung up in a guide wire then knock over a power pole. Yup it happend.. No power at the track now.

Does anyone know how to wire the auto APPS plug once it has been switched over to the manual trans ECM. I have the pin out for the ecm, but I can only find 3 common pins for A/T and M/T ECM. The 3 problems im having with the A/T APPS is I need Idle and not idle wires and sensor ground. These 3...

How would I go about getting all of the gauges to work, what other issues would I run into? I got a 2007 mega cab ram 3500 4x4 6spd for $3000, no motor everything else is there. Wanting to put the reliable dinosorus motor in there.

I have a new Air Dog II DF 165 for 05+ Dodge $650 shipped

Hooked to the sled for the first time this season today, truck would not fuel. Leaving at 4200rpm and it would fall right off, no smoke until below 2500rpm. Thought it was something with the tuning so i when back to the settings i was running last year (smarty) still the same thing. Checked the...

What are the advantages to running a 35 vs a 33? Yes they come in wider sizes, but if it was about tread contact patch a dual wheel truck would almost always out pull a single wheel truck....

Any sled pulls this year? Didnt see anything on the website. 2 events in Texas this year!!!! Would love to see a sled pull as part of the show.

I drive mostly highway miles, so I was thinking the taller tire would drop the RPM down and mabe net better MPG. Is the taller, heavier tire going to negate any highway advantages during stop and go driving. This is a 4x4 RCLB about 300hp NV4500 and 3:54 gears. I drive 65 miles a day with...

I have a set of stock 24v wheels with 285/75R16 tires I would like to sell. I only have 3 center caps. Make offer.

As the title says there will be a TDTPA sled pull at the Valair track in Mineral Wells on July 30th. Gates open at 4pm pull starts at 5pm. There will be an open pull afterward.

Up at TS I pluged my smarty in to check the settings before I pulled. I could select adjust options but when I selected connect to truck it wouldn't do anything but tell me to turn the key on then off, then back on over and over. There wasn't a communication error message. This is an S-06 on a...

Our next pull will be in Llano at Toy Land on May 21st. Address: 1920 North State HWY 16 Llano, TX 78643 This is located right behind the cement plant south of the airport on 16. There will be an open pull after the event put on by B&L Construction http://mapq.st/jbf3in

Please see if you can identify these nozzles. They are said to be II 75hp for the 04.5+ trucks. I dont think this is the case for the following reasons. 1. They dont look like any II injector I have ever seen. 2. They have 8 holes not 5 3. They say 555-2 on the side. This is the best...

I have noticed lately that there is oil on the exposed threads above the nut on my head studs. There are no oil leaks anywhere around them. I wiped them off the other day and now they are wet again. Its not alot to where it is running down the head, just enough to see that the treads are wet...