Search results

I’m looking for a friend. He wants a clean, rust free first gen dually Cummins, 4x4 preferably with a manual and extended cab. Regular or flat bed works. Stick or modified either is fine. Might be interested in a project truck that needs work but really looking for a nice ready to go truck...

I’m planning a hot street/strip build with my 2006. Shooting for 1K at the tire just to have a goal. Truck will be street driven a lot with maybe 20 strip passes a year. Big single turbo setup, Carrillo rods, cummins pistons, Hamilton street cam, big injectors, big stroker cp3, fire rings...

Yesterday, out of the blue, my serpentine belt started chirping or squealing nonstop. I’ve only driven probably 100 miles or so around town and two lane roads since it started, but it is getting progressively worse. I sprayed the belt with WD-40(all I had available at the time)with the truck...

I need a core 48re 4x4 that would work in my 2006. From my research I’d need a 2005 or later 48re because of the electric motor TV and the bosses for it in the case. I’m in South Georgia but willing to ship. Also, is there a way to make a 48re from earlier years work with my stock electronics...

Yesterday my 2006 5.9 didn’t want to start. It is stock except for HPP EFI Live tunes that have been on it for probably a year or more. The truck would turn over for around 5 seconds and then finally crank. Once running, it initially seemed to run normally. I made some short trips during the...

I'm the second owner of this boat and have had it for the last 8 years and about 80 hours of use. It has about 370 hours total. It has been service by a Stingray dealer its whole life. Always used in fresh water, no salt water ever. It was recently serviced with all the fluids changed...

This pump came off my 1995 Dodge Ram 2500 with a 47rh. It was working normally when it was removed and replace with a 215hp pump. It's located in Valdosta, GA.

I bought these off Mark Nixon on here to use in a build on my 2014, but I sold the 2014 and no longer need them. They came out of a 2013 Ram 2500, and had approximately 60,000 miles on them when removed. They were working when pulled, but I'm selling them as cores. That's how I bought them...

47re core complete with converter. I bought this to do a 47re swap on my 2014, but I sold my 2014 and no longer need the 47re. I was told it was operating when pulled other than some slipping in 2nd gear. It is a core only though and would definitely need rebuilding before putting it in...

1995 regular cab long bed Dodge Ram 2500 Cummins, 47rh. 238,000 miles. I'm the second owner and have had the truck for the last 8 years and the last 80K miles. Cosmetically the truck is pretty rough, about whats expected for a non restored 1995 Ram. The dash is cracked and the paint is...

I have a side by side set of compounds on my 1995, 366 manifold charger and 480 atmospheric. I bought it off a member on here a year or so ago. I'm not sure who made the pipes or who welded the flange on the 366. I'm not sure what the main cause is for the breakage, but the welded on flange...

I recently bought a used 2006 Cummins that the previous owner installed a TS Power Play MP8. I want to tune it with EFI Live so I tried to remove the Mp8. I assumed I could just unplug it, but when I unplugged the main connector from the Mp8 box the truck ran rough and threw a code. I cleared...

I was driving my 1995 the other day and while going down the road the tach and speedo stopped working. All other gauges continue to work normally. The truck then dropped out of overdrive. I assume because the transmission lost pcm input, but I'm not sure. I cut the truck off and then back...

I have a 1995 reg cab 4x4 that is a street and track toy. It has the original 200K mile short block. The head was recently checked out and rebuilt with stronger springs and it was cut for fire rings. The pump is a 215 built by Northeast Diesel and then tuned on the truck by Darren Morrison...

I'm thinking of going with big input and output shafts on my 2006 48re when I build it. I haven't decided which trans to go with but I'm leaning towards Garmon, Firepunk or Suncoast. What is required to make the big output shaft work with my stock T case? Is it changing the stock T case input...

I've long been planning(dreaming) a big power daily driver build. I got into diesel because of the thought of having one truck that could do it all, tow, daily drive, get decent mileage and be relatively fast. I'm starting to think the truck I've been planning isn't really possible. I built...

Bought a 4x4 47re core with converter from rjustman. The price was fair and it was delivered on time and as advertised. I would not hesitate to purchase from him again. Great seller! Sent from my iPhone using Tapatalk

Looking for a 4x4 47re or 48re complete with converter that I can use as a good core to build and use in a 68rfe swap on my 2014. Thank you Sent from my iPhone using Tapatalk

Easy to deal with and fair on prices. Shipped 2013 injectors to me in timely fashion and good condition just as advertised. Wouldn't hesitate to do business with him again. Thanks Mark Sent from my iPhone using Tapatalk

I'm pretty happy where the truck is right now, but I think it has more in it with just some tuning. It really clears up to just a haze at full throttle and the AFC is not at max fuel. I think I could go up on timing some too. The rotating assembly is stock though including the narrow-bowl...