Search results

Guys, Ive got a NV here thats built to the point of setting endplay on the mainshaft. I have not done one of these in a few years, but I seem to remember that there is a special bearing race for the mainshaft, that makes it so the race extends fully into the case. Am I correct? As of right now...

as the title says, selling my s480, or willing to trade it for the right 67-71mm s400 (83TW) has typical s400 play, was rebuilt ~2000miles ago. the .9 housing was new then, but has a crack on one side of the divider, will not affect performance. I've been running the 80 as a single, with a...

Question for those with fire ring experience. The fire ring HG kit I got from Keating includes fire rings with an OD that measures ~ 4.5 inches. The ring cross section diameter is .105" (ID at 4.29") that makes the center line of the ring a 4.395" the machine shop that I sent my head to that...

as the title says, they ran fine when they came out, good for a high timing truck with smaller bowl pistons. 425$ shipped

So I put myself in a pickle... I had always assumed an RH case is the same as an RE case.... wrong.... I was building a trans out of spare parts (basically a full manual 47re), with a full manual RE valvebody, and picked an RH case out of my pile of parts (mostly because it did not need much...

hamilton 188/220 cam, USED, has some road rash on the intake valves from the cam gear walking off. I would be running it again, But I'd like to go bigger. good for someone wanting to give it a try on a budget mindset. 200$ shipped. stock 12V USA rods, they all have a small ding that I would...

snagged this pic from Little6cylinder's photobucket, interested in what rear tire/rim setup he was using

Customer did not realize his gasket was blown until the engine ate 2 gal of oil. Now I'm left with this. The engine has less than 5k miles on it since I rebuilt it. Im thinking oring protrusion might be the cause of the failure. It was re tourqued a few times. Anyways. I need to clean it...

Does anyone know the spicer part number for a 1410 front driveshaft yoke for an np271?

fits on top of 2ndgen style valve covers, has shank style bolts that act as a rocker support as well (bolts included) has a rough polish on it. 100$ buyer pays shipping.

built this to adapt a ford Np271 to my secondgen's stock front driveshaft. accounts for the length differential and pilots the dodge flange to the ford flange yoke. 100$ shipped.

I need to build, or buy a cage for my truck this winter. Can someone tell me what is required to get a cert down to say, 10.00? I'd like to have a cage that I can still live around, and that I can keep a stock-ish dash. in what way does the cage itself need to connect to the frame under the cab?

Questions, 1 when are the axle shafts of my d60 going to break? 2 what shaft can I but that will eliminate the CAD with my stock 3.55 gears (guessing 30-31ish spline?) even if the CAD wont break, i'd rather just eliminate it. UNLESS, i have to go thru the BS of pulling the carrier to replace...

Ive got an RH output for sale. it was in my truck for about 30 miles before the OD housing broke. when the tcase came off it did so at an angle and marred up a few of the splines. all in all the output is fine. it is straight and has no defects into the minor dimension of the splines. not to...

for sale. has 50miles on a new rebuild. new 1.0 exh housing. compressor wheel has some nicks from being run without a filter. comp cover is sanded smooth, but not polished. 1500$ shipped

so its decided, i'm building a 1stgen 2wd racer. 47rh/full manual 4 link cage engine from my 94 (hammy head, 13mm pump) large twins ect ect. I decided that going fast in my 94 dually was kind of silly, when I have a 2wd frame with a newly rebuild front end, and a rotted back half. its begging...

Dually's are Fing awesome, buy my stuff With that said... I'm selling all the DRW parts from my truck. Bed -800$ (great shape, no rot with tailgate) Axle -800$ (3.55 dually D80, open dif, great shape, recent brakes) Cap-350$ lund, painted black Adaptors, trim rings and hubcaps, lug nuts. BO...

I need a housing , like yesterday. 1.0, or 1.1, maybe even a 1.25 please let me know if you have anything in stock...

for sale, 87/80 1.25 housing for the older 87 wheel, good shape, cut to hx40 flange. 150$ shipped

In need of a 1.0 or 1.1 housing ( 87TW ) for an s400. let me know. thanks -Alex