Search results

Anyone have the part number for the 12v bus exhaust manifold??

Looking for shock tower delete and shocks for the front and rear of my super street truck. Need to get rid of the shock tower for clearance on the turbocharger setup. Any idea's??

Who all is using limiting straps on the front end on a 4wd? I have not used any as of yet but looking into getting them for my 97 dodge. I am launching around 40psi right now. I don't have very good videos to check to see how much the front is lifting. It is lowered quite a bit in the front also.

I am trying to find the timing chart for dynomite's 13mm pump. Lenny is the only one over there that knows it and its hard getting ahold of him. Thanks, Cody

I am needing a haisley input shaft and bell housing adapter for a nv4500. It needs to be the long shaft that is used with the triple disk clutch. Thanks, Cody

What are the rules and classes for this years event? I called scheids and they did not know and was told to call TS. I called them and they did not know, they told me to post on comp d and see if anyone knew.

I just ordered some 390/40/17 drag radials and now looking for some 17X10 wheels for them. Its a little harder than I thought finding a 10" wide wheel for the dodge bolt pattern. Anyone know of some aluminum wheels?

Looking at a set of these tires for the drag truck, just wondering if anyone has ran them and how do you like them. I currently have toyo proxies on it right now. Hoosier Racing Tires 19276 Hoosier Pro Street D.O.T. Radial 31 X 12.50R-16 LT - 19276 Hoosier Tire Mid Atlantic hoosiermidatlantic.com

Looking for some 32" tall drag radials in either a 16" or 17" wheel. I have looked all over the website and cant find what I am looking for.

Truck currently has 305/50/20 toyo proxies. Best 60' of 1.7 but we are spinning all 4 tires when we launch. Looking at getting rid of the 20's and getting a 16" wheel and a set of cheater slicks. Truck is geared 4.10's so I would need a 32" tall tire.

2002 bone stock no mods, will only start with a shot of brake clean and will blow alot of black smoke. Truck will not idle you have to keep it above 1200rpms or it will die. Balance rates on all injectors say 0. I am thinking high return rate but was confussed that the balance rates all show 0.

Truck is throwing a P0505 code, I know what the description of the code is but does anyone have a manual that tells the troubleshooting of this code. Thanks

Truck is a 95 model and it starts and runs for about 10 seconds then dies and you can crank it again and it does the same thing. Fuel pressure checks good, how do you check the shutoff solenoid? Any input will help Thanks, Cody

Looks like I will doing some trading and getting a 94 single cab long bed, 4k springs, 370 injectors, k31 charger with .86 ar, built auto, dana 80 rear, non intercooled. Truck was sled pulling so I will start stripping the weight off as soon as we pick it up. Looking for high 11's in it. What...

Truck is throwing a P0522 code, I changed the oil pressure sending unit, checked all the wiring going into the harness all the way up to the engine. Is there anything else I can check on it?? Thanks, Cody

Got a 95 international with a dt466 it has the inline injection pump and I need to remove it to get it rebuilt. Is there a timing pin or some other reference before I pull it off. Thank, Cody

I see that borg warner is offering injectors for the cr engines now. They are alot cheaper than any other company I have seen (175 dollars new). Is anyone running these yet? They say that they are new with a 1 year warranty.

I am going a different and no longer need these two trucks. First is a 91 p-pumped sled puller. I am asking 10K for the 91 and $1750 for the 94. Engine- ported & polished head O-ringed arp head studs devils own water injection JL Machine 5 X .020 Injectors full cuts 0 Plate Oversize fuel lines...

Is anyone running one?? Is it just a reboxed fluidamper brand?

Like the title says comes with everything you need to install. 575 shipped