Search results

Needing a divided T6 turbine housing for a GT42. Let me know what you've got. Preferably a 1.01 or 1.15.

Cleaning out the shop, listing the parts I can think of off the top of my head for now but I'll add more as I dig through the rest. All prices are plus shipping unless otherwise noted or agreed upon. 2004 TIPM in perfect working order - $100 2004 dash and interior harnesses - $100 Full set...

I came across an SFI certified transmission and bellhousing shield the other day made for the 727 big block that covers the entire top of the transmission and uses the top 4 bellhousing bolts for mounting. While I know the 48re is a version of the 727, I've never had one side by side to...

Have a friend who got to digging around in his truck today and noticed that the VIN shows a C indicating the 325 as well as also showing that the truck is a manual. The motor plate however shows the 305 motor and has a 48re behind it. It's an 04 model truck obviously but he mentioned that the...

Listing for a friend. 3 injectors out of a running 2008 6.7 with 27,000 miles. Injectors have not been tested but have been stored properly since removal. Asking $175 per injector but open to offers. PM for fastest response. (working nights so won't be replying during the day)

Looking for a full set (all 4) of 2nd gen disk brake calipers and caliper brackets. Need to be in good working condition, not cores. Thanks

Looking for a divided T6 turbine housing for a GT42 Garrett. 1.15 or larger. Ideally non wastegated but I can always weld it closed.

I wanted to start this thread to gauge interest in a potential project I'm working on with a professional drag racing brake company and was looking to see if anyone else might be interested in going this route to determine if this project would be more of a one off potential or more of a...

So I'm fixing to freshen up the front axle and would rather spend the money with a vendor rather than Amazon. List of parts needed below if anyone offers them. AAM 9.25 hubs (Timken or SKF) AAM 9.25 steering u-joints Also swapping brakes over to 2nd gen calipers and rotors all the way...

Just wanted to one, show off the new brackets, and two see if anyone else might be interested in them as I've yet to find any vendors that make them for a 4" axle tube so that there's no need to buy an expensive bracket and then modify it to fit the AAM 11.5. They are cut by water jet by one...

As the title says, looking for a T6 turbing housing for a GT42 Garrett. 1.15 or 1.28 undivided preferably. Will also consider Tial housings for the right price.

Aeromotive A1000 with a handful of hours run time on it, always run with pre filter and diesel only, just have another pump I'll be running. $350obo shipped anywhere in the lower 48 All pump specs can be found here: http://aeromotiveinc.com/products-page/fuel-pumps/11101/a1000-fuel-pump/

Stripped the interior of the truck the other day as well as the useless to me engine bay stuff. I'll list what I can think of off hand but may be forgetting something so if I don't list it just ask. All parts are in very good used condition with normal wear. 100K miles on truck. Grey interior...

OEM electric tow mirrors in normal condition off my 04. $250 shipped obo PM for fastest response.

I have a brand new 194-220-110LSA Cast Cam.330"/.330" Hamilton cam that I intended on running but plans have changed and I now need a bigger cam so this one's for sale. These run $700 new, I'll do $600 shipped obo. This is a drop in cam in MOST instances but like any cam be sure to check all...

Have an 06 ECM I no longer need. $450 shipped. PM for fastest response

Have a Precision PT-98 Thumper that has been clipped to 91mm at the cover. G-Trim Turbine 1.00 T6 undivided housing. Journal bearing with normal play ready to run. Compressor cover has standard 7" radius inlet and 4" slip-on discharge. Tubine housing is 5" v-band exit. Cast compressor wheel...

So I've got a somewhat off the wall question for those of you with MUCH more knowledge of metals than I have. To put it simply, I have a friend who works for a small mom and pop machine shop that makes parts for the oilfield. Any excess material is free game for whatever they see fit. Most of...

A good friend of mine has come across Cat C7/Allison 3070 running complete setups out of the military MRAPs These are all low mileage (20,000 miles or less) combos. These are a 24 volt system combo. There are 65 of these available and likely to have 500 more before long. Price is $3200 per and...

I have a set of bone stock 6.7 injectors I bought a while ago with intentions of sending them to Exergy for enlarging. Recently bought what I needed and no longer need these. I don't remember the exact mileage on them as it's been quite a while since purchased but I do know they have less than...