Recent content by RGHodges

I am listing these parts for a friend. The parts are off his 06 puller that he is putting back on the street. Dual cp3 kit (no pumps)-$500 DDP Turbo, 74mm compressor, 1.10 housing, 2.6 cover-$1000 II stainless body 71 LPM injectors, rated at 450hp-$3500 Water Methanol System-$150 Nv4500 swap...

Up for sale is a set of ARP head studs for a 12 valve. New in box. $375 shipped. Call or text 336-401-2120. Thanks.

I have a Stainless Diesel T4 12 valve manifold I would like to trade for a T3. Prefer Stainless or Steed. Manifold is polished. Call or text 336-401-2120. Thanks.

2nd gen Spearco intercooler for sale. Has small bend in top plate. Barely noticeable and doesn't affect performance of intercooler at all. Will include boots as well. Asking $800 shipped obo. Call or text 336 401 2120. Thanks.

I have recently picked up a 96 Dodge to use as my daily driver. My WIF sensor located on the bottom of the filter is leaking and I would like to do away with it all together by using a filter with no drain on it. I researched and found the Fleetguard ff5089 will work and has the same ratings as...

I have a cast s475 83 .90 I would like to trade for an s467.7. Has around 10k street miles on it. Very minimal play either way. If anyone is interested PM me or call or text at 336 401 2120. Thanks.

I have a used Haisley street puller clutch for sale. Works with NV4500 and 5600. Bought new and was in my truck for around 5000 miles and started slipping when in the throttle hard. Street miles only, no hooks. Visually everything looks good, but I will assume it needs new discs. Asking $750...

I spent some time the other day tuning my AFC to clean up the bottom end smoke a little on my truck. I feel like I have it dialed in pretty well. It runs really clean now and spool up time is the best it has ever been in my opinion. My only problem is that I have lost some power at the same...

Industrial injection built k31, billet compressor wheel, t4 foot, hx40 flange. Wheel is a little nicked up from previous owner running without filter, but nothing I would be scared to run. Has very minimal play. Wanting to try the 467.7 so this needs to go.$1000 obo. Call or text 336-401-2120...

I have been throwing around the idea of selling my truck, so here it goes. The truck is a 1999 QCSB Laramie. Has every option available including leather. I have owned the truck for about 3 years. The truck cleans up really well. Has rust starting in drivers side rocker and passenger rear door...

Hey guys, I am running an s366 74 .80 on my p pump 24 valve right now. I love the way the truck runs with this setup, however I have one problem. I understand on this size charger, anything much over 50 psi will shorten the life if it, which I would like to avoid. I have ran my wategate...

S366 74 .80 built by Engineered Diesel, T3, billet compressor wheel, zero shaft play. $1400 shipped. Tst...

What is your guys opinion on running a bellhousing blanket on a street truck. I will be sled pulling the truck on occasion, and I know it would be wise to use one in that situation, but would you leave it on for street driving? High rpm street truck, nv4500. Would you guys recommend it or is it...

Looking for a Van Aaken v5 for 98.5-00. Let me know if anyone has one of these antiques laying around collecting dust. Pm me or get in touch with me at (336) 401-2120. Thanks.

Listing for a friend who is going back to the VP world. 175 pump, 4k springs, full cut dv, conversion lines (think they are .093), pump gear, timing case, pump mounts, crazy carl's throttle bracket, vented tappet cover, etc. Includes everything needed for p pump swap. Asking $1800 for...