Recent content by jaybuller

hello yall i have a 2wd 05 1500 ram crew cab short bed truck that is imaculate. inside and out. my question is will all the body mounts line up if i were to put it all on a 2005 ram diesel crew cab short bed 4x4 2500 diesel frame? they look the same on the out side to me but i could be wrong...

Hello this excursion is from arkansas, i got stationed here in traverse city mi this past summer. the ex is in very good condition. Zero rust on body or under it. Has a nice steel cowl induction hood painted to match. Tan leather interior, power heat front seats. 3rd row seat. Clean...

Alright guys I have two trucks...one is a 94 dodge ram 2500 with a cummins, 5 speed 4x4 that has been rolled. The drivetrain is perfect but body is shot. So I want to swap over the entire drivetrain( including rear ends) into my 05 perfect body 1500 2wd ram. Do you guys see any major hurdles I'm...

Im trying to get ahold of a 99 7.3 long block. it has forged rods and a low compression hole in it. so im going to be going through it and build it up a little. Im looking to put this thing in my daily driver 4x4 excursion. I want to end up somwhere around 550 hp mabey a tad more but i dont...

Lookin for a set of guages with piller pod, need trans temp, egt and boost. Prefferably 0-35 psi, and 0- 1500 or 1600. Am looking at isspro or autometer. Black w/red pointer.

hello ive got a very nice 2003 kawasaki z1000 street bike. it is custom painted phantom silver, tail slick kit, full muzzy 4 into 1 exaust, muzzy big bore kit(je pistons) brings the compression up from 11.1 up to 13.1.(runs on premium gas only, 92 or 93 octane.. also ups the bore from 958 to...

hello yall that have tdi jettas, escpecially the 2000 to 2006 years. im looking at a 02 and an 04 right now, both are tdi and 5 speed. one has 148,000 miles and the other 120k. are these motors good to go with that kind of mileage on them or are they nearing rebuild time? they both sound good...

my blazer is up for sale. family needs money so it has to go.

I have a p7100 pumped 4bt i am runnin in my 89 k5 blazer... well now that i have been drivin it around a while i am ggoing to turn it up... Does anyone know where i could look to see what this turbo is good up to as far as boost numbers go? like the hx35 is good to 35psi and anything over is...

Im gonna go watch them.....should be a good time.

I cant believe somthing this small is keeping me from progressing with the swap.... but i cant find any and i think ive tried them all..... the studs that the clutch slave cyl mount on did not come with nuts on them when i got the bell housing.... and ive tried and bought every possible nut i...

Ok im working on final engine placment in my blazer so i need someone with a nv4500 sittin around to get me some measurments.... i need the measurment from the top of the input shaft to the highest part of the shift tower... also the measurment from the top of the input to the top of the front...

its in very good condition. i will take 55 dollars shipped to you.(in the lower 48)

I have a cummins p7100 4bt 130 hp engine. It is the 1839 CPL. I am wanting to see about getting new injectors for it but i dont know what to order? are these supposed to be just like the 12v ppump injectors with the 145* angle and around 265 bar pop off? Would a regular ole set of 145* 5x10s...

enjoy,, plans are to go with 181 dvs, injectors not sure yet, 3000 gsk. and a he341.. well see where it goes from there.