Search results

Spare parts from many different rebuilds. Some of the things included are. Overdrive compressor Spare intermediate shaft Cut off intermediate shaft (to line up OD clutches) Sonnax servo TCS servo 47+48 forward ring gear Every size OD selective spacer Every size plastic spacer Xtra thrust...

8 months old. 3" lift on a 3rd gen. $300 shipped. 250 local pickup. Buyer pays paypal fees. Located in central ct

Good shape. No cracks or starter grinds. $175 shipped

1 piece billet input shaft. I purchased it from ATS. I believe it's made be sonnax. Never raced, no boosted launches, no twisted splines. $500 shipped

https://www.youtube.com/watch?v=kvCHiCeLueY I'm still chasing a vibration at highway speeds that I can't seem to solve. The video is the truck on jack stands in the garage in 2wd. Tires removed. Listen for the noise when I apply the brakes to load it up. Noise only occurs under load...

I just finished installing dual cp3's. Loaded smarty on 9. It's regular revo, no tnt. From 60-120 wot pull egts maxed out at 1175 which seems kind of low. It stayed right at 53-55 psi up to 3400 rpm where I lifted. At idle in gear it is at 450 and about 650 degrees at 65 mph. My concern...

I got a vibration between 65-80 on the highway. There is no vibration while I'm coasting. Slight vibration under load. It most noticeable when I'm barely on the throttle, not accelerating or coasting. I removed the front driveshaft, no change. I just installed a new 5" aluminum driveshaft...

For those installing one of these at home check the length on the transfer case input before installing. I took off a little over a half inch with a die grinder. The transfer case input was noticeably longer than the stock 23 spline . But the splines on the billet output seemed longer so I...

I pulled the Trans out to put in all billet shafts and found this. I had to use a shop press to get the intermediate off of the overdrive piston support. It has 30-40k on it since it was last apart. I read through big blues sticky and I'm going to drill the case for more fluid to the sprag...

What is the difference between a TCS 300m and 300 maraging intermediate shaft? . Going through their catalog any shaft made with 300 maraging has a higher torque capacity. I'm preparing for a future 1000hp daily driver. Trans is out getting aermet and a 29 spline output. Might as well do...

What have you used to remove rust scale off of the underside of the truck? I didn't know if there was anything out there that's brush on and will turn rust into a paint able surface. I really don't want to sandblast. I'm afraid I will have sand end up in the engine Trans or axle somehow.

I'm working on a 47re and I ran into a snag. I ended up needing a .020 thicker selective shim. The problem is I am at the max .115 on the od brake clutch and od piston. I was thinking of splitting the difference and using .010 selective shim and calling it good. Opinions?

I got a mid 80's case skids teer with a worn out 188d. I'm about to pull the motor for a rebuild. It could use more power and I happened to find a turbo and manifold off a case 207d. It has a roosta master injector pump. Has anyone ever done something like this? Or is it a bad idea

I have a set of injectors out of my 04.5. The bodies have 71k on them and the tips have 15k. New control valves were installed when I bought the flux 2 tips. I replaced them because my truck had a slight rough idle and haze at idle and while driving. After I put the new injectors in I had the...

I have been looking around for new injectors. Exergy seems to be the best deal at $360 a piece for stock bosch injectors. I would rather get stainless bodys if I can. Any feedback on anywhere else to buy them? My current symptoms are a constant haze while driving. Idle is not smooth but I...

Who can I send my injectors to for testing and rebuilding besides f1? I have not had good luck with f1 rebuilds so I need to find someone who can do it right the first time. Or where can I buy new ones at a reasonable price, thanks

I am looking for a a frame for a 4wd quad cab long bed 3500 dodge. Email me if you have one in the connecticut area davem3261@yahoo.com. I don't check my pm's often

I was running a tst for the longest time and I now run a smarty. My only complaint is that the midrange power is not close to as strong as the tst. I can stand on it at 1900rpm and the boost will hit 35 and then at about 2500rpm the boost will start to rapidly climb to 55psi. Is this the way...

I have an cp3 off of an 06. 78k miles on it. $500 shipping included. You can email me at davem3261@yahoo.com

Let me know what you have and the mileage on it. Anything considered. I would also take a lbz or lmm pump Send a pic to davem3261@yahoo.com