Search results

Two pumps for sale 4cyl a pump , ag gov , 6cyl mw pump , ag gov , I don't have any info , they were pulled for some sort of conversion. I cannot say they are in running condition . 300$ each ? Make an offer buyer pays shipping and they will be packaged and documented with insurance by...

Bought from a member and never ran . My plans have changed . Asking 1600$ best offer . Thanks

I'm looking into going this route , and can't find any info on this set up . It's very clean but I can't tell much from the picture . I don't see any bracing for the primary mount , also wondering if the hot pipe is a short radius schd 80 pipe fitting , or pie cut .

Looking for . Adjustable pump gear P pump gear case P pump front cover Thanks

I normally try and exhaust all options before posting on here , but this has me stumped. ill lay out my set up first and explain my issue second. -63/68/12 gated over a box s480. - spring gate from stainless diesel -ddp stage 4 injectors - timing at 22* - pump is a 215 bought off a comp...

First off I apologize im not very familiar with common rail electronics I'm asking for a friend and this is not my area of expertise . I searched the site and google searched the site I can't find anything similar . Friends truck is an 06 , 90hp nozzles , stock over 475 , bag o parts , efi by...

A friend and I Removed the factory block and overloads , Common rail springs with one coil cut . Added traction bars , swapped in the freshly rebuilt dana 60 . The truck rides and drives so much better now, before it was miserable to drive . Best thing I've ever done to it

160hp 854 pump for sale , has 4ks , dv's are stock . came off running truck. my friend bought a benched 180 to swap in its place . the pump has no fuel plate .... it was not ran without one, the plate was pulled to go in the other pump. I am selling this for a friend but the pump is in my...

Timkens with studs and rotors from rock auto 350$ to my door Gonna have a brand new front end here in a little bit

I need one for a new compound setup Thanks

One owner car with 100k on it and all 100% original with the exception of a documented timing belt change at 80k . My plans are- buy injectors, I was thinking Kerma's hot swap , so there's no down time . Attempt to get a malone chip for the tuning , if anyone has any input it would be...

It's that time of year again , pull is this Saturday at the Dixon may fair . Who's all going ? Last year was a decent turnout . With no event in redding this year I'm hoping it'll be better.

The subject is really broad but bear with me as I try to explain my issue. The trans is a full billet suncoast originally for a vp truck . it's been converted over to run in my 12v by the local trans guy. My wiring harness was destroyed, so I bought a tfod-3 kit and had him install it...

in the next couple months i would like to have compounds on my truck. my current charger is a 63/68/.91 t4 and i would like to run a 480 under it . im looking to get into a gated housing for that 63. so far ive found the .83 with a t4 foot and real small volutes and this type in the picture...

I'm looking for either a 68mm gated turbine housing or an external gate and t4 gate plate . It's for a compound set up and my 63 is non gated .

I got this phatshaft 62 about 3 years ago, I rebuilt it , and ran it for about 2 years . I pulled it off to go another route and let a friend use it ( sort of a community charger) . When I gave it to him everything seemed tight , no in and out play and normal side to Side. I suggested he...

I'm running this as a single . Mods are, 215 benched maxed at 600cc plate set half way . 63-68 .91 non gated , Ddp 4's , 4k's , studs and o rings, timing at 22*. air dog at pressure set from factory. Built suncoast race trans manual vb . I see about 10 psi at 75mph I've been able to hit 60psi...

Just thought I would share with you guys what I did to mount my shifter . It bolts between the mounts for the center seat and the seat it self . It's a street truck and I didn't want to give up the center console and seat . So this is what I came up with. 4wd high is no issue, neutral and low...

Let me know if anyone has one they can sell. Thanks

So I managed to toast my wire harness running to my PCM . I have a sun coast race billet 47re , was originally for a 24v . the harness has been swapped and Its in my 97. When I toasted the harness to my PCM the trans went Into what I assume is a limp mode . I now have only second and third ...