Search results

3.5” lift front Add a leaf in rear with Air bags for hauling Dana 60 Front 3.54 Gears Open carrier, new axle joints, brakes, rotors, wheel bearing, ball joints. Dana 80 Rear welded and stress relieved, disc brakes, completely rebuilt axle 35” BFG All Terrains on 16 x 10 Alum rims. Mcgard...

1994 12V IH Block and Head. This is the motor out of my big truck that was the first to break 1300 hp. Scheids Parts: 14mm head studs Drag Cam 24V tappets HD Push Rods 14mm Main studs HD Rod Bolts Block Stiffener Scheid shot peened marine rods 13mm Scheid race pump 1200cc capable 5500 rpms...

Let me know what ya got. Have some 5 x .014" set at 280 bar I would trade, new nozzles..

Well a recent freind and neighbor from over on PSN died this spring at Silver Lake. We are all going up this coming weekend to tear up the dunes in memory of Will Iott. Silver Lake memorial G2G - Page 13 - Powerstroke Nation Should be a decent turnout. All are welcome to come hang out with...

Looking for a good used one. Let me know. Thanks Adam

Central Michigan Performance Diesel is putting on a dyno day, tug a truck, burn outs and what have ya.... Location: 2640 N School Rd Weidman MI 48893 Starts 10:00 AM $65 for 3 Pulls on the Dyno First come first serve get on the list and get on, no guarantee that you will get on, completely...

I have a Complete 94 160hp 6BT 150,000ish miles Cummins that I would swap for a 4BT. Thanks Adam

Truck: Theft recovery Ford Super duty 2001 Ex Cab Short Box 4x4 3.73 Gears 295-75R-16 BFG ATs 47RH HTS 93% Torque Convertor Gear Vendors overdrive 2.01 to 1 Final Drive Ratio 70 MPH 8-9 PSI Boost, 700-800 Deg EGT, 1500 RPMs Engine: 95 12valve 175hp Stock head bolts to 150 ft/lbs 60 lb valve...

Can I get some info on this? I would like to try one on my next conversion. Please PM me pricing as well.

Have a buddy that has a 99 auto with an engine computer part number R5083996AA engine serial # 56594344 his computer went bad and apperently these are year specific. I have a computer part number 3942336 that came off a 98 or 99. Does anyone know if you can swap these? Apparently new...

We had to move a 98,000lb plastic pellet rail car today at work so we could access it with a bulk truck. Didn't know what the outcome was going to be....... Backin Up Towing Victory Dance

Looking for one that will bolt on the back of the 241 T-Case. Adam Cell 989-621-9806

I was going to do a CR swap, but decided to do another 12V. This motor sat over winter so it has some rust on the manifold side. It was pulled from a rollover, motor is complete with all accessories and wiring connectors (they were cut from truck harness). Engine # 57074649 305 HP Build...

What are you guys running? SCS has there shafts and drive flanges for $1095. Stock dana replacements are $125 so I am doing that for now. I towed a 9000lb 30ft semi trailer on the gooseneck with my welded rear over the weekend must have fatigued it, never thought i would have a problem...

Just bought it, rode it one weekend, not what I am looking for. $115.00 shipped http://www.hondapartsworld.com/perfexlongtravelsuspensionkits.aspx

Complete take outs from truck, truck was a roll over. Not sure on the gear ratio.. 3.73? $900 for both front and rear. Will consider partial trades for 12mm head studs, DLD or DHD T-case for auto, 47RH trans core, 16cm housing for HX-35, S362. Adam cell 989-621-9806

So who has the best combo and what are you using? I was thinking: 95 12v 160 Pump Stock Turbo 5x.012 Sticks 022 DVs Stock head bolts lubed with moly to 135 ft/lbs 18 degrees timing 3k gsk or washers Some type of cam plate Auto trans 3.73 gears 295 tires 7200 lbs What 22 mpg and 325 hp to the...

LittleRed asked me to see what you guys have found to be the best MPG settings on your electronics. He is on his way to Texas with an empty 25' gooseneck getting about 14ish. He has tried some different combo's without much luck. Truck is a reg cab stick 3.54 gears stock tires, maybe they are...

I have had more than one gasket on this thing, second trans it has been on and still leaks, heard something about early batch being machined wrong on the sealing surface and not being flat. Anyone else have these issues?

I think Brett did this, anyone have pics of the modified plate bolted up to the motor mount mounting holes? Thanks Adam