Search results

Has anyone done it? Recommendations on where to install the injector? IS 375 ml/ min too much?

If my truck sits for more than a day, it sounds like it starts on one cylinder after giving it plenty of fuel and turning the motor over for a few seconds, it shakes for about 5 seconds and it runs fine. Starts fine after sitting for an hour or two. Feels like the injector lines are mostly empty...

I was installing a 4k gsk on my truck, got one side done and went to turn the motor over and the retainer caught the side of the pump as I was turning the motor over. I saw it stop as I was turning the motor immediately but now the shaft that holds the governor springs has play in it when I...

tested about 4,000 miles ago and are in great shape. $450 shipped

60/71/14 s300 no shaft play $675 shipped 443-677-1580 Eric

5k gsk $225 Shipped

Looking to downgrade from my 5k to a 3 or 4k gsk plus $100.

HX-35 upgraded to the 6 blade 60mm "super 40" wheel. No exessive play in the shaft at all and has not been ran since the work was done. I was going to use it for twins but decided to stick with a single turbo. $675 Shipped. Eric 443-677-1580

I had this turbo machined and built to fit the 60mm 6 blade hx40 compressor wheel a few months ago in hopes to use it as a top turbo for twins. Plans changed and more important things came up so i'm leaving my s300 single on the truck. The hx35 has not been ran at all since the work has been...

Is there a difference in the non- intercooled heads vs. the intercooled 2nd gen heads? or are the injector holes different?

It is for my 97 2nd gen. Preferably a completely stock head. Thanks.

S360 over a 26cm 3B. I built a brick outhouse bottom turbo mount to keep the weight off the exhaust manifold/manifold ears (I had 2 ears break without it). It comes with EVERYTHING. Manifold spacer (not needed but I put it in there) Longer manifold studs to be used with spacer S360 top turbo...

My truck will start and immediately shut off. I thought it was the govenor springs because I was messing with them so I tried starting it with some throttle and got the same result with a ton of smoke. I felt the shutoff solenoid during the startup process and it pulls up when the key is in...

The one that bolts into the side of the block. Thanks

2002 Yamaha R1. It has chrome rims, professionally polished frame, 24k miles oil changed religiously, I have put 13k miles on the bike in 3 years, new clutch, brand new pilot power 2ct tires, runs EXCELLENT, yoshimira pipe, new brake pads all around. I had compliments everywhere I went on how...

Included: Hx35/40 top charger (7 blade 60mm), fresh build HT3B Primary charger Custom built hotpipe Downpipe Charge pipe Intake pipe Intercooler pipe Air Filter All clamps and boots 5" v-band for downpipe Oil feed lines for hx35 and HT3B Oil Drain lines Manifold Spacer Longer manifold studs...

I am getting the parts together to rebuild my current twins to a s360 over a 3b. Sourceauto has an hx40 flange (v-band) but it says it will work with an s300 if the s300 is machined to fit the hx40 flange. Does anyone know what gets machined and how to tell if its already done?

I am looking for a small turbo (t25 maybe) that is not water cooled (mainly because I don't want to deal with water lines). Does anyone have any that they know offhand would fit the build? I can do water lines if it is really necessary but I have a limited amount of workspace since its for a...

I currently have an hx35 over a 26cm housing 3b. It runs well but I am rebuilding them and will have an s360 over a 3b but I have the choice of a 26cmhousing 3b or a 32cm housing 3b. It will be used for towing so I don't want it to be too laggy on the primary but I really just want some...